CAD CAM EDM DRO - Yahoo Group Archive

Re: stepper controller boards

on 2002-01-18 18:28:40 UTC
Hi San,

Are these John K's board? I noticed he no longer has these pix on his
site. I'd be cautious trying to "parallel" two PC power supplies.
Without some sort of series resistor, they might not want to share
current! I suppose one could use two supplies, NOT connected together,
and put two steppers on each (or even one).

Alan KM6VV

santorelli333 wrote:
>
> Just upploaded pictures of a complete stepper driver cirquit to the
> photo album"Stepper driver circuits" it is a 3 axis but since the
> single axis drive schematic is included and this is the same for all
> 3 axis you can just ad one more to the circuit and the transistors
> are good for up to 5 amps each so you could connect 2 pc-power
> supplies in paralell if you need more amps (if you need even more,
> replacing the transistors should be an easy undertaking)
>
> San

Discussion Thread

dave_ace_me 2002-01-18 16:07:11 UTC stepper controller boards Carol & Jerry Jankura 2002-01-18 16:17:55 UTC RE: [CAD_CAM_EDM_DRO] stepper controller boards DRigotti@A... 2002-01-18 16:30:47 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards Chris L 2002-01-18 16:43:37 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards santorelli333 2002-01-18 16:44:14 UTC Re: stepper controller boards cncdxf 2002-01-18 17:15:07 UTC Re: stepper controller boards Alan Marconett KM6VV 2002-01-18 17:57:14 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards Alan Marconett KM6VV 2002-01-18 18:28:40 UTC Re: stepper controller boards dave_ace_me 2002-01-18 18:38:06 UTC oh Moderator... Re: stepper controller boards dave_ace_me 2002-01-18 18:42:20 UTC Re: stepper controller boards Gary Wheeler 2002-01-19 14:13:25 UTC Re: stepper controller boards Area51tats@a... 2002-01-19 15:14:12 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-20 12:38:23 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Smoke 2002-01-20 12:54:03 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Jerry Kimberlin 2002-01-20 17:02:53 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Daniel J. Statman 2002-01-20 17:12:02 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-20 18:17:17 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Jerry Kimberlin 2002-01-20 18:36:38 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards dave_ace_me 2002-01-20 19:27:02 UTC (rant) should be titanium was Re: stepper controller boards wanliker@a... 2002-01-20 20:35:18 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-21 06:07:16 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards