CAD CAM EDM DRO - Yahoo Group Archive

Re: stepper controller boards

Posted by dave_ace_me
on 2002-01-18 18:42:20 UTC
Hi Bob,

I figure that it is better to be save than sorry.
So I posted a note to the moderator to pull the pictures
until we get approval.

Although I have seen these published on a web page
well, at least the schematic.

Let's get an approval to post them with full
credit to the author and/or post his web page
so he can get the credit he deserves !

Dave



--- In CAD_CAM_EDM_DRO@y..., "cncdxf" <cncdxf@a...> wrote:
> San,
> Those drawing are Copyrighted material! The author is a
> friend of mine. He has been notified!
>
> Bob
>
>
>
>
> --- In CAD_CAM_EDM_DRO@y..., "santorelli333" <san3@s...> wrote:
> > Just upploaded pictures of a complete stepper driver cirquit to
the
> > photo album"Stepper driver circuits" it is a 3 axis but since the
> > single axis drive schematic is included and this is the same for
> all
> > 3 axis you can just ad one more to the circuit and the
transistors
> > are good for up to 5 amps each so you could connect 2 pc-power
> > supplies in paralell if you need more amps (if you need even
more,
> > replacing the transistors should be an easy undertaking)
> >
> > San

Discussion Thread

dave_ace_me 2002-01-18 16:07:11 UTC stepper controller boards Carol & Jerry Jankura 2002-01-18 16:17:55 UTC RE: [CAD_CAM_EDM_DRO] stepper controller boards DRigotti@A... 2002-01-18 16:30:47 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards Chris L 2002-01-18 16:43:37 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards santorelli333 2002-01-18 16:44:14 UTC Re: stepper controller boards cncdxf 2002-01-18 17:15:07 UTC Re: stepper controller boards Alan Marconett KM6VV 2002-01-18 17:57:14 UTC Re: [CAD_CAM_EDM_DRO] stepper controller boards Alan Marconett KM6VV 2002-01-18 18:28:40 UTC Re: stepper controller boards dave_ace_me 2002-01-18 18:38:06 UTC oh Moderator... Re: stepper controller boards dave_ace_me 2002-01-18 18:42:20 UTC Re: stepper controller boards Gary Wheeler 2002-01-19 14:13:25 UTC Re: stepper controller boards Area51tats@a... 2002-01-19 15:14:12 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-20 12:38:23 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Smoke 2002-01-20 12:54:03 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Jerry Kimberlin 2002-01-20 17:02:53 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Daniel J. Statman 2002-01-20 17:12:02 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-20 18:17:17 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Jerry Kimberlin 2002-01-20 18:36:38 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards dave_ace_me 2002-01-20 19:27:02 UTC (rant) should be titanium was Re: stepper controller boards wanliker@a... 2002-01-20 20:35:18 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards Edwin S. Katz 2002-01-21 06:07:16 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller boards