Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
Posted by
peteryco@r...
on 2002-01-25 05:41:51 UTC
Hello Lee,
that is common use.
A good way for long term run is to turn a centering ring that
fits into the conuses of the chuck and the rotary table.
And screw it down.
For single setup and low cutting forces it is enough
screw or clamp the chuk on the R-table and center it with
the indicator.
Have fun
Sven Peter
----- Mensaje Original -----
De: studleylee <indigo_red@...>
Fecha: Jueves, Enero 24, 2002 9:08 pm
Asunto: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
that is common use.
A good way for long term run is to turn a centering ring that
fits into the conuses of the chuck and the rotary table.
And screw it down.
For single setup and low cutting forces it is enough
screw or clamp the chuk on the R-table and center it with
the indicator.
Have fun
Sven Peter
----- Mensaje Original -----
De: studleylee <indigo_red@...>
Fecha: Jueves, Enero 24, 2002 9:08 pm
Asunto: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
> Hi,
> I was wondering how others have mounted 3Jaw chucks on rotary tables.
> I have an enco phaseIII 10" or so. It has a taper (MT# ? I have
> to
> RTM) hole in the center. Just fishing for ideas.
> -Lee
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@...
> [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
studleylee
2002-01-24 19:08:41 UTC
Rotary table 3-Jaw chuck mount?
Jon Elson
2002-01-24 22:31:06 UTC
Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
peteryco@r...
2002-01-25 05:41:51 UTC
Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
ballendo
2002-01-25 06:51:00 UTC
Re: Rotary table 3-Jaw chuck mount?
studleylee
2002-01-25 14:51:25 UTC
Re: Rotary table 3-Jaw chuck mount?
Robert Allen & Marsha Camp
2002-01-25 18:39:01 UTC
Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
krlux
2002-01-25 21:28:13 UTC
Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
Fitch R. Williams
2002-01-26 07:44:53 UTC
Re: [CAD_CAM_EDM_DRO] Rotary table 3-Jaw chuck mount?
ballendo
2002-01-27 05:35:10 UTC
Re: Rotary table 3-Jaw chuck mount?
studleylee
2002-01-28 13:10:56 UTC
Re: Rotary table 3-Jaw chuck mount?