Re: [CAD_CAM_EDM_DRO] drilling techniques for plastic to get specific sized hole?
Posted by
Rich D.
on 2002-01-31 22:40:41 UTC
Lloyd,
Use a SHARP drill with the lip rake ground to zero (a small flat on
the leading edges). Don't step drill. Drill at low RPM to avoid heat
and ease it thru. Soluable oil mix or water may help.
Plastic will always produce a tight hole but, using a sharp drill,
especially at the corners, will help.
Oversize reaming may be the only other recourse.
RichD
Lloyd Leung wrote:
~ ~~ ~ ~ ~~ ~~____~,~~ ~~~~
\------/ |00|_[]_[]__||0
.|_CMRy_|-|__|________|_|,
__________''oo__oo__---"0=0=0"=o[]o\\______________________________
-==Rich=-=Colorado Midland Railway=-=cmsteam@...=-Atlanta-
----------See my web site: <http://cmsteamer.homestead.com/> ------
Use a SHARP drill with the lip rake ground to zero (a small flat on
the leading edges). Don't step drill. Drill at low RPM to avoid heat
and ease it thru. Soluable oil mix or water may help.
Plastic will always produce a tight hole but, using a sharp drill,
especially at the corners, will help.
Oversize reaming may be the only other recourse.
RichD
Lloyd Leung wrote:
>--
> I have either, UMHW, Polyethylene, or something like cutting boards.
>
> I'd like to know the technique for drilling plastic.
>
> I want a 1/2" hole... however, when I slide it over my 1/2" precision
> ground rod, the hole is too small...
>
> --
> Lloyd Leung
> Lloyd@...
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
~ ~~ ~ ~ ~~ ~~____~,~~ ~~~~
\------/ |00|_[]_[]__||0
.|_CMRy_|-|__|________|_|,
__________''oo__oo__---"0=0=0"=o[]o\\______________________________
-==Rich=-=Colorado Midland Railway=-=cmsteam@...=-Atlanta-
----------See my web site: <http://cmsteamer.homestead.com/> ------
Discussion Thread
Lloyd Leung
2002-01-31 20:47:21 UTC
drilling techniques for plastic to get specific sized hole?
Lloyd Leung
2002-01-31 21:39:11 UTC
Clearification RE: drilling techniques for plastic to get specific sized hole?
Rich D.
2002-01-31 22:40:41 UTC
Re: [CAD_CAM_EDM_DRO] drilling techniques for plastic to get specific sized hole?
Jon Elson
2002-01-31 23:16:43 UTC
Re: [CAD_CAM_EDM_DRO] drilling techniques for plastic to get specific sized hole?
ballendo
2002-02-01 10:54:58 UTC
Re: Clarification RE: drilling techniques for plastic to get specific sized hole?
Raymond Heckert
2002-02-01 20:38:09 UTC
Re: [CAD_CAM_EDM_DRO] drilling techniques for plastic to get specific sized hole?
Jon Elson
2002-02-01 22:50:21 UTC
Re: [CAD_CAM_EDM_DRO] drilling techniques for plastic to get specific sized hole?