Re: tensioned ballscrew
Posted by
ballendo
on 2002-02-20 07:27:48 UTC
Doug,
Hadn't seen this post when I asked your traverse speed...
So you're planning for 500ipm?
Okay, so what's the cost of a "not-cheap" ballnut, compared to the
time, effort, materials, etc. of the traveling supports?
Ballendo
P.S. Is this a ground or rolled screw? Are you using one or two?
Hadn't seen this post when I asked your traverse speed...
So you're planning for 500ipm?
Okay, so what's the cost of a "not-cheap" ballnut, compared to the
time, effort, materials, etc. of the traveling supports?
Ballendo
P.S. Is this a ground or rolled screw? Are you using one or two?
--- In CAD_CAM_EDM_DRO@y..., "Doug Harrison" <prototype@c...> wrote:
> ----- Original Message -----
> From: ballendo <ballendo@y...>
> > Sounds like a lot of work, especially when there's a simple,
proven,
> > often-used solution.
> >
> > Spin the nut.
>
> I was going in this direction until I came to the same conclusions
that Les
> outlined. Cheap ballnuts are not made to spin at 2000rpm. These
are six
> inches long with square bodies and external return tubes.
>
> Rotating nuts are still in the back-up plan. So are rack and
pinion.
>
> Doug
Discussion Thread
Doug Harrison
2002-02-18 18:45:25 UTC
tensioned ballscrew
JanRwl@A...
2002-02-18 20:06:13 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
vrsculptor
2002-02-18 20:20:57 UTC
Re: tensioned ballscrew
JanRwl@A...
2002-02-18 20:23:44 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
Bill Vance
2002-02-18 21:13:37 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
ballendo
2002-02-19 04:16:18 UTC
Re: tensioned ballscrew
John H.
2002-02-19 04:26:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: tensioned ballscrew
ballendo
2002-02-19 05:20:34 UTC
Gears vs. belts (and NOT about M/D's ) was Re: tensioned ballscrew
Les Watts
2002-02-19 08:20:59 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
JanRwl@A...
2002-02-19 13:46:15 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
Doug Harrison
2002-02-19 16:40:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: tensioned ballscrew
Doug Harrison
2002-02-19 16:41:55 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
Doug Harrison
2002-02-19 17:13:49 UTC
Re: [CAD_CAM_EDM_DRO] tensioned ballscrew
Chris L
2002-02-19 19:52:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: tensioned ballscrew
ballendo
2002-02-20 04:28:28 UTC
Re: tensioned ballscrew redux
ballendo
2002-02-20 07:27:48 UTC
Re: tensioned ballscrew
ballendo
2002-02-20 08:18:57 UTC
A/B (anti-backlash) rack/pinion drive was Re: tensioned ballscrew
Kevin P. Martin
2002-02-20 08:23:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: tensioned ballscrew
Shelbyville Design & Signworks
2002-02-20 08:24:11 UTC
Re: tensioned ballscrew
Doug Harrison
2002-02-20 12:54:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: tensioned ballscrew
ballendo
2002-02-20 15:10:07 UTC
These prices are nuts ! was Re: tensioned ballscrew
Doug Harrison
2002-02-20 17:39:39 UTC
Re: [CAD_CAM_EDM_DRO] These prices are nuts ! was Re: tensioned ballscrew
Doug Harrison
2002-02-20 18:06:22 UTC
Re: [CAD_CAM_EDM_DRO] A/B (anti-backlash) rack/pinion drive was Re: tensioned ballscrew