8-wire 1/2coil stepper?
Posted by
keongsan
on 2002-05-07 19:16:01 UTC
Hi,
The gecko paper for motor connection
http://www.geckodrive.com/support/pdf/motor_connections.pdf
shows 5 diagrams for connecting motors
(A) 4 wire
(B) 6 wire half-winding virtually = parallel
(C) 6 wire full-winding exactly = series
(D) 8 wire parallel = 3% more efficient than half-winding (B)
(E) 8 wire series = no advantage compared with full winding.
(D) shows all 4 coils wired up as compared with (B). I am worried
about wiring the motor as I believe there may be a possibility that
the coils may be connected to oppose each other.
Question: Is it possible to add a sixth possibility (F) for 8 wires
and sacrifice that 3% more efficient. (for added confidence before I
embark on this, hope those who have followed this route successfully
(or even disastrously) will post their experience
(F) 8 wires half-winding exactly = (B)
where only 1 coil of one phase is wired, and the other coil is
ignored.
Thanks in advance
keongsan
The gecko paper for motor connection
http://www.geckodrive.com/support/pdf/motor_connections.pdf
shows 5 diagrams for connecting motors
(A) 4 wire
(B) 6 wire half-winding virtually = parallel
(C) 6 wire full-winding exactly = series
(D) 8 wire parallel = 3% more efficient than half-winding (B)
(E) 8 wire series = no advantage compared with full winding.
(D) shows all 4 coils wired up as compared with (B). I am worried
about wiring the motor as I believe there may be a possibility that
the coils may be connected to oppose each other.
Question: Is it possible to add a sixth possibility (F) for 8 wires
and sacrifice that 3% more efficient. (for added confidence before I
embark on this, hope those who have followed this route successfully
(or even disastrously) will post their experience
(F) 8 wires half-winding exactly = (B)
where only 1 coil of one phase is wired, and the other coil is
ignored.
Thanks in advance
keongsan
Discussion Thread
keongsan
2002-05-07 19:16:01 UTC
8-wire 1/2coil stepper?
mariss92705
2002-05-07 19:54:51 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-07 19:56:39 UTC
RE: [CAD_CAM_EDM_DRO] 8-wire 1/2coil stepper?
keongsan
2002-05-07 20:06:45 UTC
Re: 8-wire 1/2coil stepper?
keongsan
2002-05-07 20:14:06 UTC
Re: 8-wire 1/2coil stepper?
Tony Jeffree
2002-05-08 00:59:23 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 06:33:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?
Tony Jeffree
2002-05-08 12:42:38 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 13:03:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?
tonyjeffree
2002-05-08 13:35:33 UTC
Re: 8-wire 1/2coil stepper?
mariss92705
2002-05-08 14:46:25 UTC
Re: 8-wire 1/2coil stepper?
keongsan
2002-05-08 18:46:06 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 18:56:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?