Re: 8-wire 1/2coil stepper?
Posted by
keongsan
on 2002-05-08 18:46:06 UTC
Hi,
reset the camtronics board for 2 A and rewired the 8-wire stepper 1/2
coil mode. The result of my little adventure: (dos from floppy)
. 1/2 coil full coil
Master5 25 ipm 16
DeskNC 43 22
TurboCNC 45 15
The motor was hardly warm even at 2A setting. When a 8-wire stepper
is given as 2A 2.4 ohm (meaning 5V?) would this be the rating for
parallel connection? Would this mean that if one only connect 1/2
coil one could use it for a high amperage? Wonder if it is really 2A.
Could it be 4A rating I wonder? How do one test for this? (no ratings
on the motor)
Tempted to connect to the Gecko and try for 4A 1/2 coil.
Feedback please and thank you very much
keongsan
reset the camtronics board for 2 A and rewired the 8-wire stepper 1/2
coil mode. The result of my little adventure: (dos from floppy)
. 1/2 coil full coil
Master5 25 ipm 16
DeskNC 43 22
TurboCNC 45 15
The motor was hardly warm even at 2A setting. When a 8-wire stepper
is given as 2A 2.4 ohm (meaning 5V?) would this be the rating for
parallel connection? Would this mean that if one only connect 1/2
coil one could use it for a high amperage? Wonder if it is really 2A.
Could it be 4A rating I wonder? How do one test for this? (no ratings
on the motor)
Tempted to connect to the Gecko and try for 4A 1/2 coil.
Feedback please and thank you very much
keongsan
Discussion Thread
keongsan
2002-05-07 19:16:01 UTC
8-wire 1/2coil stepper?
mariss92705
2002-05-07 19:54:51 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-07 19:56:39 UTC
RE: [CAD_CAM_EDM_DRO] 8-wire 1/2coil stepper?
keongsan
2002-05-07 20:06:45 UTC
Re: 8-wire 1/2coil stepper?
keongsan
2002-05-07 20:14:06 UTC
Re: 8-wire 1/2coil stepper?
Tony Jeffree
2002-05-08 00:59:23 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 06:33:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?
Tony Jeffree
2002-05-08 12:42:38 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 13:03:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?
tonyjeffree
2002-05-08 13:35:33 UTC
Re: 8-wire 1/2coil stepper?
mariss92705
2002-05-08 14:46:25 UTC
Re: 8-wire 1/2coil stepper?
keongsan
2002-05-08 18:46:06 UTC
Re: 8-wire 1/2coil stepper?
Tim Goldstein
2002-05-08 18:56:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: 8-wire 1/2coil stepper?