Re: Basic EMC question
Posted by
exeric1
on 2002-07-21 15:12:12 UTC
This is a sidenote to my question. Does anyone make a PC board that
provides a well regulated 80 volts along with 3 high power drivers
ala Gecko drives? Also does the EMC output only exist on the parallel
port or can the output be redirected on a bus that the inboard
circuit board would be capable of using?
Eric
provides a well regulated 80 volts along with 3 high power drivers
ala Gecko drives? Also does the EMC output only exist on the parallel
port or can the output be redirected on a bus that the inboard
circuit board would be capable of using?
Eric
--- In CAD_CAM_EDM_DRO@y..., "exeric1" <exeric1@y...> wrote:
> I've been doing some reading about EMC and understand the push
behind
> it was to create a standard control system that isn't hardware
> dependent. The big question: is the control board function
> implemented in software on the PC? That would explain the big deal
> about an operating system that can output commands in real time - I
> understand that standard windows can't hack it and Unix,Windows NT
> and Linux can. My other related question is this: Why is it so
> important to have a non-proprietary control system? It seems you
will
> still need a separate outboard power supply and drivers that WILL
be
> proprietary for each servo/stepper installation. I don't get it.
I'm
> not being a smart ass, I'm just learning. If it could ALL be
> implemented inside the PC including power supply for the drivers
and
> drivers themselves then it would make sense to me.
>
> Eric
Discussion Thread
exeric1
2002-07-21 14:22:27 UTC
Basic EMC question
exeric1
2002-07-21 15:12:12 UTC
Re: Basic EMC question
Jon Elson
2002-07-21 22:04:15 UTC
Re: [CAD_CAM_EDM_DRO] Basic EMC question
Jon Elson
2002-07-21 22:07:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Basic EMC question
Brian Pitt
2002-07-21 23:39:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Basic EMC question
exeric1
2002-07-22 00:01:35 UTC
Re: Basic EMC question
Brian Pitt
2002-07-22 00:32:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Basic EMC question
Peter Homann
2002-07-22 00:42:54 UTC
LCD or LED DRO Readout.
turbulatordude
2002-07-22 03:27:54 UTC
Re: LCD or LED DRO Readout.
Keith Bowers
2002-07-22 06:22:02 UTC
Re: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.
James Owens
2002-07-22 06:45:46 UTC
Re: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.
Jon Elson
2002-07-22 10:01:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Basic EMC question
JanRwl@A...
2002-07-22 19:40:54 UTC
Re: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.
Tony Jeffree
2002-07-22 22:30:35 UTC
Re: LCD or LED DRO Readout.
Ian W. Wright
2002-07-23 01:18:27 UTC
Re: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.
Stan Stocker
2002-07-26 06:25:39 UTC
Re: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.
Peter Homann
2002-07-26 07:33:09 UTC
RE: [CAD_CAM_EDM_DRO] LCD or LED DRO Readout.