CAD CAM EDM DRO - Yahoo Group Archive

Re: fanuc 6mb

Posted by Fedia
on 2002-07-26 09:09:13 UTC
>
>
>________________________________________________________________________
>
>Message: 3
> Date: Thu, 25 Jul 2002 12:47:02 -0500
> From: Jon Elson <elson@...>
>Subject: Re: fanuc 6mb
>
>cnc002@... wrote:
>
>> The one thing you do need to find out is if the
>>"Executive" software, or control parameters are available on disk so you
>>don't have to enter those by hand if they get corrupted or have been deleted
>>for whatever reason. If the machine and control parameters are still in the
>>control and have not been corrupted, that is the machine will still run a
>>program that is in the control, then you should be able to upload those to
>>your PC for safe keeping.
>>
>
>If they have any paper tapes that came with the machine, get them. these may be
>the only copies of the executive and diagnostics that are properly configured for
>the machine setup. You may need to resurrect the paper tape reader long enough to
>read these into a PC. If the memory backup battery dies (like when the control
>has been turned off for a month) then you need to reload the executive and any
>parameter and configuration tapes. If there were any manuals, especially
>programming, operation and maintenance books, you will certainly want those,
>too.
>
>Jon
>
>
>
>________________________________________________________________________
>
Jon,
Sorry, but Fanuc 6 has bubble memory from Hitachi as a standard, which
is on magnetic principle and should retain data more than 10 years.
The drawback is that a memory board worked more than 10 years could
give defect loops and all data are usually lost. Fanuc proposes a CMOS
replacement board, about $1500, but for newer Fanuc 6 controls. If the
ROM board is with 2764 and power supply number ends with xxx-B002, the
control can be upgraded.
Best regards,

--
Fedia Buznik
fedia@...

RAIS Ltd.
www.rais-bg.com
58, Dimcho Debelianov Str.
4400 Pazardjik, Bulgaria
Tel. +359 34 444255
+359 34 445221
Fax: +359 34 443738

Discussion Thread

ptkent01 2002-07-24 13:51:37 UTC fanuc 6mb Jon Elson 2002-07-24 21:38:24 UTC Re: [CAD_CAM_EDM_DRO] fanuc 6mb cnc002@a... 2002-07-25 04:35:32 UTC Re: [CAD_CAM_EDM_DRO] fanuc 6mb Fedia 2002-07-25 09:22:42 UTC fanuc 6mb Jon Elson 2002-07-25 10:44:27 UTC Re: [CAD_CAM_EDM_DRO] fanuc 6mb Peter Homann 2002-07-25 15:54:13 UTC Speed of Tapping Head? turbulatordude 2002-07-26 04:11:53 UTC Re: Speed of Tapping Head? Peter Homann 2002-07-26 05:21:09 UTC RE: [CAD_CAM_EDM_DRO] Re: Speed of Tapping Head? jmkasunich 2002-07-26 08:09:22 UTC Re: Speed of Tapping Head? Fedia 2002-07-26 09:09:13 UTC Re: fanuc 6mb doug98105 2002-07-26 13:44:21 UTC Re: Speed of Tapping Head? turbulatordude 2002-07-26 16:35:48 UTC Re: Speed of Tapping Head? turbulatordude 2002-07-26 16:44:46 UTC Re: Speed of Tapping Head? - tap styles Jon Elson 2002-07-26 22:03:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Speed of Tapping Head? Jon Elson 2002-07-26 22:10:38 UTC Re: [CAD_CAM_EDM_DRO] Re: fanuc 6mb Peter Homann 2002-07-27 00:15:19 UTC RE: [CAD_CAM_EDM_DRO] Re: Speed of Tapping Head? Peter Homann 2002-07-27 00:16:34 UTC RE: [CAD_CAM_EDM_DRO] Re: Speed of Tapping Head? jmkasunich 2002-07-27 12:19:29 UTC Re: Speed of Tapping Head? - tap styles Brian Pitt 2002-07-27 12:36:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Speed of Tapping Head? - tap styles doug98105 2002-07-27 16:30:25 UTC Re: Speed of Tapping Head? - tap styles turbulatordude 2002-07-27 20:00:13 UTC Re: Speed of Tapping Head? - tap styles Fedia 2002-07-28 23:50:40 UTC fanuc 6mb