CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] ringing sound

Posted by Dan Mauch
on 2002-08-18 06:40:33 UTC
Sounds like your cable is not properly wired even though you have
continuity on each wire it would seem like the phases aren't correct.
Look at your good cable and then make sure the bad cable is wired
exactly the same as the good cable.
Dan

-----Original Message-----
From: keongsan [mailto:keongsan@...]
Sent: Sunday, August 18, 2002 3:22 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] ringing sound

Message 46731 of 48546

> --- In CAD_CAM_EDM_DRO@y..., JanRwl@A... wrote:
> > In a message dated 27-Jun-02 20:13:52 Central Daylight Time,

> > Both, actually. But one of the little "things in life" one must
> deal with,
> > like friction! If you suddenly reverse-step stepper-motors, the
> normal
> > "ringing" that might be handled just fine if stepping stopped for
a
> time, or,
> > another axis were "suddenly" chosen. BUT, if you reverse-step
the
> SAME axis,
> > the motor is "still ringing", so the motor can integrate this
into
> a phantom
> > step.

Hi,

Having a bit of problem with the G201 driver again. I think it is the
cable.

The y-axis works fine, but the x-axis either doesn't respond or gave
very faint sound but does't move.

Tried switching axis. This time the x-axis is OK but the y-axis is
not responding. Can't remember what I did next, I think I switch
cable or something. If memory not failing, I think the problem
follows the cable. Checked the cable with meter - seem OK.

Reconnecting, this time the fauty axis gave a ringing sound, but no
movement. Tried to search the archives for "ringing" only found the
above.

Ringing sound plus no movement is a symtom of what problem?

Thanks

keongsan


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Discussion Thread

JanRwl@A... 2002-06-27 17:31:54 UTC Re: [CAD_CAM_EDM_DRO] I am loosing one step. weir! luisguillermo98 2002-06-27 18:12:59 UTC Re: I am loosing one step. weir! JanRwl@A... 2002-06-27 18:25:50 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! luisguillermo98 2002-06-27 18:39:56 UTC Re: I am loosing one step. weir! JanRwl@A... 2002-06-27 19:59:26 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! Jon Elson 2002-06-27 23:38:59 UTC Re: [CAD_CAM_EDM_DRO] I am loosing one step. weir! Dan Mauch 2002-06-28 06:21:06 UTC RE: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! luisguillermo98 2002-07-02 12:32:49 UTC Re: I am loosing one step. weir! JanRwl@A... 2002-07-02 17:02:13 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! luisguillermo98 2002-07-02 18:44:54 UTC Re: I am loosing one step. weir! JanRwl@A... 2002-07-02 20:43:25 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! luisguillermo98 2002-07-03 15:41:42 UTC Re: I am loosing one step. weir! luisguillermo98 2002-07-03 16:16:10 UTC Re: I am loosing one step. weir! Dennis Cranston 2002-07-03 16:56:25 UTC RE: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! Thomas Mayfield 2002-07-03 16:57:55 UTC [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! JanRwl@A... 2002-07-03 22:42:08 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! JanRwl@A... 2002-07-03 22:43:17 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! Doug Harrison 2002-07-04 07:33:01 UTC Re: [CAD_CAM_EDM_DRO] Re: I am loosing one step. weir! keongsan 2002-08-18 03:21:57 UTC ringing sound Dan Mauch 2002-08-18 06:40:33 UTC RE: [CAD_CAM_EDM_DRO] ringing sound turbulatordude 2002-08-18 07:32:35 UTC Re: ringing sound cadcamcenter 2002-08-18 08:42:49 UTC Re: ringing sound