CAD CAM EDM DRO - Yahoo Group Archive

Speed - Parallel vs serial ( was Re: Motor

on 2002-09-03 07:02:55 UTC
Is there a relationship for calculation for the speed difference ?

I am replacing some NEMA23's double stack with some NEMA34's, single
stack. both 200 step/rev.

The NEMA23's worked fine, but I need to put them in a tight place
where the 34 is too big.

TurboCNC on my 486-100 reports 11,000hz as the maximum reliable
speed. and I had been running the 23's at 10k.

also, any easy way to determine how to wire in series? currently the
8 wire 34's are wired in parallel.

Dave





--- In CAD_CAM_EDM_DRO@y..., "mariss92705" <mariss92705@y...> wrote:
> Gene,
>
> Your'e right on both counts. The motor runs cooler in series as
well.
> Use series if you don't have to have high speed. Low speed torque
> will be the same.
>
> Mariss
>
> --- In CAD_CAM_EDM_DRO@y..., Gene <capper@i...> wrote:
> > What is the difference between connecting a 8 wire motor either
> > parallel or series? If you use series then do you use 1/2 rated
> amps?
> > Is there lower speed and power in series?

Discussion Thread

Mike Snodgrass 2002-03-05 12:02:18 UTC Motor mariss92705 2002-03-05 17:36:17 UTC Re: Motor Gene 2002-07-13 19:24:04 UTC Motor mariss92705 2002-07-13 20:41:00 UTC Re: Motor turbulatordude 2002-09-03 07:02:55 UTC Speed - Parallel vs serial ( was Re: Motor Robert Campbell 2002-09-03 07:19:23 UTC Re: [CAD_CAM_EDM_DRO] Speed - Parallel vs serial ( was Re: Motor turbulatordude 2002-09-03 16:36:21 UTC Speed - Parallel vs serial ( was Re: Motor Bob Simon 2002-09-03 19:32:21 UTC Siemens drives in current mode Robert Campbell 2002-09-03 19:36:21 UTC Re: [CAD_CAM_EDM_DRO] Speed - Parallel vs serial ( was Re: Motor cadcamcenter 2002-09-03 21:41:06 UTC Speed - Parallel vs serial ( was Re: Motor cadcamcenter 2002-09-03 21:57:29 UTC Speed - Parallel vs serial ( was Re: Motor turbulatordude 2002-09-04 04:35:15 UTC 8 wire half or Serial ? ( was Speed - Parallel vs serial ( was Re: Motor mariss92705 2002-09-04 07:35:13 UTC 8 wire half or Serial ? ( was Speed - Parallel vs serial ( was Re: Motor turbulatordude 2002-09-04 11:01:43 UTC 8 wire half or Serial ? ( was Speed - Parallel vs serial ( was Re: Motor cadcamcenter 2002-09-04 17:07:47 UTC 8 wire half or Serial ? ( was Speed - Parallel vs serial ( was Re: Motor JJ 2002-09-04 17:35:24 UTC RE: [CAD_CAM_EDM_DRO] Speed - Parallel vs serial ( was Re: Motor cadcamcenter 2002-09-04 19:06:10 UTC Speed - Parallel vs serial ( was Re: Motor JJ 2002-09-05 04:12:04 UTC RE: [CAD_CAM_EDM_DRO] Speed - Parallel vs serial ( was Re: Motor turbulatordude 2002-09-05 04:25:36 UTC Speed - Parallel vs serial ( was Re: Motor