Re: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
Posted by
Matt Shaver
on 2002-09-26 18:18:02 UTC
On Thursday 26 September 2002 03:52 pm, you wrote:
NAND gate output (that you're using) to the input of a 7407 Hex Open
Collector Buffer. The outputs of the 7407 can be connected together, and that
signal needs to be pulled up to +5Vdc through a 1k-10k resistor:
Obligatory ASCII Schematic (view in fixed width font):
Xidx -\
=|)o--|>-+-/\/\/\/-O 5V
Xhsw -/ |
|
Yidx -\ |
=|)o--|>-+
Yhsw -/ |
|
Zidx -\ |
=|)o--|>-+
Zhsw -/ |
|
O To Home Input
=|)o- 7400 NAND Gate
-|>- 7407 Open Collector Buffer
Good Luck,
Matt
> Just didn't know if I could parallel the gatesYou can't wire-OR together the outputs of the 7400, you need to connect each
> output.
NAND gate output (that you're using) to the input of a 7407 Hex Open
Collector Buffer. The outputs of the 7407 can be connected together, and that
signal needs to be pulled up to +5Vdc through a 1k-10k resistor:
Obligatory ASCII Schematic (view in fixed width font):
Xidx -\
=|)o--|>-+-/\/\/\/-O 5V
Xhsw -/ |
|
Yidx -\ |
=|)o--|>-+
Yhsw -/ |
|
Zidx -\ |
=|)o--|>-+
Zhsw -/ |
|
O To Home Input
=|)o- 7400 NAND Gate
-|>- 7407 Open Collector Buffer
Good Luck,
Matt
Discussion Thread
dakota8833
2002-09-26 06:24:51 UTC
Gecko Fault/Reset Manager
awallin25
2002-09-26 10:56:57 UTC
Re: Gecko Fault/Reset Manager
dakota8833
2002-09-26 12:52:48 UTC
Re: Gecko Fault/Reset Manager
Matt Shaver
2002-09-26 18:18:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
JJ
2002-09-27 05:18:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
Ray Henry
2002-09-27 06:28:45 UTC
Re: Re: Gecko Fault/Reset Manager
Matt Shaver
2002-09-27 11:42:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
dakota8833
2002-10-01 12:06:26 UTC
Gecko Fault/Reset Manager
vrsculptor
2002-10-01 14:21:28 UTC
Re: Gecko Fault/Reset Manager
dakota8833
2002-10-01 16:02:20 UTC
Re: Gecko Fault/Reset Manager
Frank de Beer
2002-10-02 00:27:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
Frank de Beer
2002-10-02 04:48:20 UTC
encoder 12V --> 5V
Jon Elson
2002-10-02 09:25:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Fault/Reset Manager
Erik Reikes
2002-10-02 13:30:37 UTC
Re: encoder 12V --> 5V