Re: Center tapped transformer
Posted by
mariss92705
on 2002-10-23 09:23:33 UTC
Tim,
You can also connect a full bridge rectifier across the end wires and
get the following:
1) +42V and -42V (ground the centertap).
2) +42V and +84V (ground the "-" end of the bridge; the center tap is
then +42V).
Option (2) is useful if you have a mix of high speed and low speed
axies; use the higher voltage for the high speed ones.
Mariss
You can also connect a full bridge rectifier across the end wires and
get the following:
1) +42V and -42V (ground the centertap).
2) +42V and +84V (ground the "-" end of the bridge; the center tap is
then +42V).
Option (2) is useful if you have a mix of high speed and low speed
axies; use the higher voltage for the high speed ones.
Mariss
--- In CAD_CAM_EDM_DRO@y..., "Tim Goldstein" <timg@k...> wrote:
> I have a transformer that is center tapped on the secondary. Voltage
> from the center tap to either end is 30 v. from end to end it is 60
> volts. I know that if I want 60 volts I just connect the ends to the
> bridge and tape off the center tap. How do I connect it if I want 30
> volts at the maximum amperage possible? I realize I can connect
from one
> end to the center and get the 30 volts, but it seems like I am
missing
> out on amperage by not somehow using the other half of the coil.
>
> Tim
> [Denver, CO]
Discussion Thread
Chris and Dee
2002-10-21 14:07:19 UTC
Speaking of encoders....
C.S. Mo
2002-10-21 14:37:14 UTC
Re: [CAD_CAM_EDM_DRO] Speaking of encoders....
Chris and Dee
2002-10-21 17:51:13 UTC
Re: Speaking of encoders....
Tim Goldstein
2002-10-22 23:56:32 UTC
Center tapped transformer
Matt Shaver
2002-10-23 00:10:23 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Tim Goldstein
2002-10-23 00:18:09 UTC
RE: [CAD_CAM_EDM_DRO] Center tapped transformer
echnidna
2002-10-23 03:22:29 UTC
Re: Center tapped transformer
Alan Matheson
2002-10-23 03:28:26 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
caudlet
2002-10-23 05:38:22 UTC
Re: Center tapped transformer
Keith Bowers
2002-10-23 07:57:11 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
mariss92705
2002-10-23 09:23:33 UTC
Re: Center tapped transformer
Jon Elson
2002-10-23 10:39:14 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Jon Elson
2002-10-23 10:43:22 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Alan Marconett KM6VV
2002-10-23 11:14:33 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
JanRwl@A...
2002-10-23 13:48:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
JanRwl@A...
2002-10-23 14:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Raymond Heckert
2002-10-23 18:26:00 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
caudlet
2002-10-24 05:14:35 UTC
Re: Center tapped transformer
bjammin@i...
2002-10-24 05:47:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
caudlet
2002-10-24 08:19:57 UTC
Re: Center tapped transformer
Dave Dillabough
2002-10-24 12:11:43 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dave Dillabough
2002-10-24 12:11:44 UTC
RE: [CAD_CAM_EDM_DRO] Center tapped transformer
Raymond Heckert
2002-10-24 20:51:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Jim Brown
2002-10-24 22:58:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
echnidna
2002-10-24 23:45:11 UTC
Re: Center tapped transformer
echnidna
2002-10-25 00:21:02 UTC
RE: Re: Center tapped transformer
JanRwl@A...
2002-10-25 09:22:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Matt Shaver
2002-10-26 00:42:25 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dan Mauch
2002-10-26 06:18:48 UTC
RE: [CAD_CAM_EDM_DRO]Single point cnc threading
tommoser3246
2002-10-26 06:48:43 UTC
Re: Center tapped transformer
Matt Shaver
2002-10-26 14:45:22 UTC
Re: [CAD_CAM_EDM_DRO]Single point cnc threading
Jon Elson
2002-10-26 18:25:29 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dave Kowalczyk
2002-10-26 18:33:55 UTC
NAMES get together
Jon Elson
2002-10-26 18:38:54 UTC
Re: [CAD_CAM_EDM_DRO]Single point cnc threading
jmkasunich
2002-10-30 12:09:34 UTC
Re: NAMES get together
Ray Henry
2002-10-30 20:31:24 UTC
Re: Re: NAMES get together
Cardinal.Eng
2002-10-31 03:47:16 UTC
Re: NAMES get together
wbhinkle@a...
2002-10-31 09:03:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: NAMES get together
jmkasunich
2002-10-31 14:23:47 UTC
Re: NAMES get together
Ray Henry
2002-11-01 04:36:59 UTC
Re: Re: NAMES get together
jmkasunich
2002-11-01 06:04:36 UTC
Re: NAMES get together