Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Posted by
Dave Dillabough
on 2002-10-24 12:11:43 UTC
Look at the center tap wire. If it is a loop or 2 wire ends then you can
split them apart to get 2 30 volt windings which can be paralleled to
double the secondary current. To make sure that you get the phasing of the
2 windings right connect a light bulb in series with the primary to limit
the current. Parallel the secondary windings and apply power with no load.
If the bulb lights the seconday windings are out of phase, reverse them and
try again. You should get the proper voltage on the secondary with the bulb
unlit.
At 12:55 AM 10/23/02 -0600, you wrote:
split them apart to get 2 30 volt windings which can be paralleled to
double the secondary current. To make sure that you get the phasing of the
2 windings right connect a light bulb in series with the primary to limit
the current. Parallel the secondary windings and apply power with no load.
If the bulb lights the seconday windings are out of phase, reverse them and
try again. You should get the proper voltage on the secondary with the bulb
unlit.
At 12:55 AM 10/23/02 -0600, you wrote:
>I have a transformer that is center tapped on the secondary. Voltage
>from the center tap to either end is 30 v. from end to end it is 60
>volts. I know that if I want 60 volts I just connect the ends to the
>bridge and tape off the center tap. How do I connect it if I want 30
>volts at the maximum amperage possible? I realize I can connect from one
>end to the center and get the 30 volts, but it seems like I am missing
>out on amperage by not somehow using the other half of the coil.
>
>Tim
>[Denver, CO]
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects
>goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to
>reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>sister site to the CCED group, as many of the same members are there, for
>OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
>THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Chris and Dee
2002-10-21 14:07:19 UTC
Speaking of encoders....
C.S. Mo
2002-10-21 14:37:14 UTC
Re: [CAD_CAM_EDM_DRO] Speaking of encoders....
Chris and Dee
2002-10-21 17:51:13 UTC
Re: Speaking of encoders....
Tim Goldstein
2002-10-22 23:56:32 UTC
Center tapped transformer
Matt Shaver
2002-10-23 00:10:23 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Tim Goldstein
2002-10-23 00:18:09 UTC
RE: [CAD_CAM_EDM_DRO] Center tapped transformer
echnidna
2002-10-23 03:22:29 UTC
Re: Center tapped transformer
Alan Matheson
2002-10-23 03:28:26 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
caudlet
2002-10-23 05:38:22 UTC
Re: Center tapped transformer
Keith Bowers
2002-10-23 07:57:11 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
mariss92705
2002-10-23 09:23:33 UTC
Re: Center tapped transformer
Jon Elson
2002-10-23 10:39:14 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Jon Elson
2002-10-23 10:43:22 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Alan Marconett KM6VV
2002-10-23 11:14:33 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
JanRwl@A...
2002-10-23 13:48:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
JanRwl@A...
2002-10-23 14:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Raymond Heckert
2002-10-23 18:26:00 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
caudlet
2002-10-24 05:14:35 UTC
Re: Center tapped transformer
bjammin@i...
2002-10-24 05:47:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
caudlet
2002-10-24 08:19:57 UTC
Re: Center tapped transformer
Dave Dillabough
2002-10-24 12:11:43 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dave Dillabough
2002-10-24 12:11:44 UTC
RE: [CAD_CAM_EDM_DRO] Center tapped transformer
Raymond Heckert
2002-10-24 20:51:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Jim Brown
2002-10-24 22:58:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
echnidna
2002-10-24 23:45:11 UTC
Re: Center tapped transformer
echnidna
2002-10-25 00:21:02 UTC
RE: Re: Center tapped transformer
JanRwl@A...
2002-10-25 09:22:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Center tapped transformer
Matt Shaver
2002-10-26 00:42:25 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dan Mauch
2002-10-26 06:18:48 UTC
RE: [CAD_CAM_EDM_DRO]Single point cnc threading
tommoser3246
2002-10-26 06:48:43 UTC
Re: Center tapped transformer
Matt Shaver
2002-10-26 14:45:22 UTC
Re: [CAD_CAM_EDM_DRO]Single point cnc threading
Jon Elson
2002-10-26 18:25:29 UTC
Re: [CAD_CAM_EDM_DRO] Center tapped transformer
Dave Kowalczyk
2002-10-26 18:33:55 UTC
NAMES get together
Jon Elson
2002-10-26 18:38:54 UTC
Re: [CAD_CAM_EDM_DRO]Single point cnc threading
jmkasunich
2002-10-30 12:09:34 UTC
Re: NAMES get together
Ray Henry
2002-10-30 20:31:24 UTC
Re: Re: NAMES get together
Cardinal.Eng
2002-10-31 03:47:16 UTC
Re: NAMES get together
wbhinkle@a...
2002-10-31 09:03:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: NAMES get together
jmkasunich
2002-10-31 14:23:47 UTC
Re: NAMES get together
Ray Henry
2002-11-01 04:36:59 UTC
Re: Re: NAMES get together
jmkasunich
2002-11-01 06:04:36 UTC
Re: NAMES get together