Re: Pin removal, Amphenol plug????

JJ,

Yes, that's exactly right. The link to a catalog picture of the
breakdown that Bill H posted last night shows the configuration.

I'm hoping I can find some new pins tommorrow at one of our local
electronic suppliers. The existing pins would still work, but are so
goobered up with sloppy soldering jobs that it'd be much cleasner to
start with new pins.

Doug

--- In CAD_CAM_EDM_DRO@y..., "JJ" <jj5412@e...> wrote:
> These Amp connectors are a little different. The pins have a flange
> machined on them, which is used to capture the pin between two
phenolic
> disks. The only way to do it is disassemble the connector by
removing
> the snap ring.
>
> Regards,
> JJ
>
> Be Kind, Be Careful, Be Yourself
>
>
>
> > -----Original Message-----
> > From: Alan Marconett KM6VV [mailto:KM6VV@a...]
> > Sent: Sunday, October 27, 2002 5:24 PM
> > To: CAD_CAM_EDM_DRO@y...
> > Subject: Re: [CAD_CAM_EDM_DRO] Pin removal, Amphenol plug????
> >
> >
> > Hi Doug,
> >
> > This is just a guess, but if the pins work like Amphenol RS-232
pins,
> > the removal tool is a thin tube that is split, and will slide
over the
> > pin from the backside of the connector. A thin tube rolled
> > up from shim
> > brass might work, if you want to home-brew a tool.
> >
> > Alan KM6VV
> >
> > doug98105 wrote:
> > >
> > > Hello Group,
> > >
> > > Amphenol plug #20-33P....
> > >
> > > The right angle fitting on the cable of my mill's Haas 4th axis
head
> > > broke. It's a 3/8" armored cable. I have to remove the wires
from
> > > the plug connector on the opposite end of the cable, pull the
wires
> > > back through and replace the right angle fitting.
> > >
> > > I don't see how the pins are pushed out of the Amphenol
connector.
> > > Or maybe the connector body comes apart somehow to allow the pin
> > > removal. Anyhow, it's not obvious. It's an 11 pin connector.
> > >
> > > I checked Amphenol's website to look for a breakdown of my
> > > connector. Their search function didn't seem to recognize the
part
> > > number, they may have a new numbering system since nothing
appeared
> > > close to my number series.
> > >
> > > Anyone have an idea how to get these pins out of the
> > connector body??
> > >
> > > thanks,
> > >
> > > Doug
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@y...
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k...
> > [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com
> > to reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> http://groups.yahoo.com/group/jobshophomeshop I consider this to
be a
> sister site to the CCED group, as many of the same members are
there,
> for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/