Re: stepper controller - help
Posted by
vrsculptor
on 2002-11-16 12:19:19 UTC
--- In CAD_CAM_EDM_DRO@y..., JanRwl@A... wrote:
so they clearly have NO clue how a stepper with windings rated at,
say, 4 amps, 3 volts....
but I am CERTAIN some E.E.'s in here like you, Mariss, etc., can do
so admirably.
Jan,
I'm with you on this. I did at one point go to www.geckodrive.com
and read the stepper motor white papaers. I think I even undertood
what this was all about... for about 10 minutes anyway.
I ended up using servo's and Gecko 320's... its a whole lot easier,
no lost steps, and, in the end, cheaper.
Roger
> Dan: For quite a time, now, I have been slightly frustrated that98% of the members of our group are more "machinists" than "E.E.'s",
so they clearly have NO clue how a stepper with windings rated at,
say, 4 amps, 3 volts....
but I am CERTAIN some E.E.'s in here like you, Mariss, etc., can do
so admirably.
Jan,
I'm with you on this. I did at one point go to www.geckodrive.com
and read the stepper motor white papaers. I think I even undertood
what this was all about... for about 10 minutes anyway.
I ended up using servo's and Gecko 320's... its a whole lot easier,
no lost steps, and, in the end, cheaper.
Roger
Discussion Thread
Boris Maraz
2002-11-16 04:57:10 UTC
stepper controller - help
Dan Mauch
2002-11-16 06:37:24 UTC
RE: [CAD_CAM_EDM_DRO] stepper controller - help
jeffalanp
2002-11-16 08:35:19 UTC
Re: stepper controller - help
JanRwl@A...
2002-11-16 10:23:58 UTC
Re: [CAD_CAM_EDM_DRO] stepper controller - help
Tom de Witt
2002-11-16 11:52:40 UTC
RE: [CAD_CAM_EDM_DRO] stepper controller - help
vrsculptor
2002-11-16 12:19:19 UTC
Re: stepper controller - help
William Scalione
2002-11-16 17:59:57 UTC
Re: [CAD_CAM_EDM_DRO] stepper controller - help
John Johnson
2002-11-17 09:09:57 UTC
Re: [CAD_CAM_EDM_DRO] stepper controller - help
foxwhole2000
2002-12-06 03:15:09 UTC
Re: stepper controller - help
jeffalanp
2002-12-06 11:32:36 UTC
Re: stepper controller - help
jagco1998
2002-12-06 15:54:23 UTC
Re: stepper controller - help
George Erhart
2002-12-06 16:15:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help
jeffalanp <xylotex@h...
2002-12-06 16:19:37 UTC
Re: stepper controller - help
George Erhart
2002-12-06 16:47:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help
foxwhole2000 <foxwhole2000@y...
2002-12-06 19:27:45 UTC
Re: stepper controller - help
jeffalanp <xylotex@h...
2002-12-06 20:24:59 UTC
Re: stepper controller - help
Brian
2002-12-07 11:01:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help
George Erhart
2002-12-07 12:32:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help
Brian
2002-12-07 14:32:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help