CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help

Posted by George Erhart
on 2002-12-07 12:32:18 UTC
Brian,

Part numbers are:

GW0000F - 8 leads - wire for any configuration
GW0000E - 6 leads - unipolar
GW0000H - 4 leads - parallel bipolar
GW0000L - 4 leads - serial bipolar

I ordered mine from Kim Controls: http://www.kim-controls.com

I had to send them E-mail to find the "on-line" ordering page for
the cable leads. Here is a direct link the the page:

http://www.kim-controls.com/PacSci/Step/cabling.htm

They charged $5 per cable and ~$5 for UPS ground shipping.
I ordered them Fiday morning and got an e-mail notification of
UPS shipping with tracking number that afternoon. In the e-mail
they sent about the cable link, they indicated that if a particular
cable was not in stock it would take a week to get it.

BTW, I ordered the GW0000F because they had 14 in stock
and I can wire them any way I want.

Good luck,

George
----- Original Message -----
From: "Brian" <ka1bbg@...>
> Hi, i have 6 powermax II steppers, no leads, do you have order # and
> address? May i have? thanks,brian f.

Discussion Thread

Boris Maraz 2002-11-16 04:57:10 UTC stepper controller - help Dan Mauch 2002-11-16 06:37:24 UTC RE: [CAD_CAM_EDM_DRO] stepper controller - help jeffalanp 2002-11-16 08:35:19 UTC Re: stepper controller - help JanRwl@A... 2002-11-16 10:23:58 UTC Re: [CAD_CAM_EDM_DRO] stepper controller - help Tom de Witt 2002-11-16 11:52:40 UTC RE: [CAD_CAM_EDM_DRO] stepper controller - help vrsculptor 2002-11-16 12:19:19 UTC Re: stepper controller - help William Scalione 2002-11-16 17:59:57 UTC Re: [CAD_CAM_EDM_DRO] stepper controller - help John Johnson 2002-11-17 09:09:57 UTC Re: [CAD_CAM_EDM_DRO] stepper controller - help foxwhole2000 2002-12-06 03:15:09 UTC Re: stepper controller - help jeffalanp 2002-12-06 11:32:36 UTC Re: stepper controller - help jagco1998 2002-12-06 15:54:23 UTC Re: stepper controller - help George Erhart 2002-12-06 16:15:28 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help jeffalanp <xylotex@h... 2002-12-06 16:19:37 UTC Re: stepper controller - help George Erhart 2002-12-06 16:47:47 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help foxwhole2000 <foxwhole2000@y... 2002-12-06 19:27:45 UTC Re: stepper controller - help jeffalanp <xylotex@h... 2002-12-06 20:24:59 UTC Re: stepper controller - help Brian 2002-12-07 11:01:41 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help George Erhart 2002-12-07 12:32:18 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help Brian 2002-12-07 14:32:06 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper controller - help