CAD CAM EDM DRO - Yahoo Group Archive

Re: Math for constant speed ellipse

on 2003-01-07 15:01:48 UTC
> If you hold the speed constant along the _inside_ edge of the path,
then the
> speed along the _outside_ edge of the path will be faster when
going around
> a curve, compared with going straight.
>

Step + Direction based CNC Controller translate all
driving instructions before motion, they are based on
the cutter center line.
Directly supported moves are circular and linear only.

Indirectly all circular moves are elliptical in nature
because of the possible different resolutions or effects
of scaling on individual axeses.

Speeds are computed based on this resolution for the dominant
drive axes in effect.
The acuracy is corsely anglined to the grit pattern and is never
precise specially on controllers that allow for a 3rd axes departure
concurrently.

Elliptical shapes are converted by the CAM Processor.
Usually it is broken down into linear moves or on better
ones into arcs then posted as G-Code.

Good Luck

Discussion Thread

Todd Fleming 2002-12-27 18:35:47 UTC Math for constant speed ellipse Les Watts 2002-12-28 15:47:44 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Yesamazza@a... 2002-12-28 16:15:31 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Todd Fleming 2002-12-28 16:39:22 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Todd Fleming 2002-12-28 16:45:08 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Les Watts 2002-12-29 08:05:19 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Bill Vance 2002-12-29 12:09:12 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Les Watts 2002-12-29 14:56:29 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Todd Fleming 2002-12-29 16:51:46 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Bill Vance 2002-12-29 16:52:26 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse jcc3inc <jccinc@o... 2003-01-02 17:32:11 UTC Re: Math for constant speed ellipse Todd Fleming 2003-01-05 12:12:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Math for constant speed ellipse Mariss Freimanis <mariss92705@y... 2003-01-05 18:00:59 UTC Re: Math for constant speed ellipse Jan Kok 2003-01-05 23:29:11 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Kevin P. Martin 2003-01-06 07:46:32 UTC RE: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Nigel Bailey 2003-01-06 08:56:42 UTC RE: [CAD_CAM_EDM_DRO] Math for constant speed ellipse - kepler? Todd Fleming 2003-01-06 19:52:52 UTC RE: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Todd Fleming 2003-01-06 20:16:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Math for constant speed ellipse Todd Fleming 2003-01-06 20:33:51 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Todd Fleming 2003-01-06 20:45:19 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse Mariss Freimanis <mariss92705@y... 2003-01-07 02:25:25 UTC Re: Math for constant speed ellipse Jan Kok 2003-01-07 03:09:18 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse bjammin@i... 2003-01-07 07:16:30 UTC Re: [CAD_CAM_EDM_DRO] Math for constant speed ellipse torsten98001 <torsten@g... 2003-01-07 15:01:48 UTC Re: Math for constant speed ellipse