Re: water vapor plasma
Posted by
dvideohd <jrobinson46@c...
on 2003-01-13 01:09:20 UTC
"Mike Snodgrass" <snarf@s...> wrote:
*****************
What boggles my mind is that this has popped up quietly. It is light
enough to Gantry Mount. Runs on the power of two hair dryers, and
puts out a beam slightly cooler than the surface of the sun.
It does not get into how precise the beam is - or how accurate the
cutter... But at $600 - it is worth checking out.
It plays into the Gantry Mount interchangeable ENM-Plasma cutter idea
very well.
** Harbor Product Post ****************
Cut, Weld and Braze With One Machine!
This portable unit uses water vapor to cut sheet metal, stainless
steel, aluminum and copper up to 1/8'' thick. Cuts cleaner, hotter,
faster with less damage to the surrounding area than gas cutting.
Continuous operation for 12-30 minutes
Inverter technology power supply
Spare parts kit
Specifications:
Input power: 220V, 10 amps, 60 Hz
Operating time on one filling: 15-18 min.
Maximum water consumption: 8.5 oz. per hr.
Jet flame temperature: 14,400° F (8000° C)
Cutting capacity: 1/16'' (steel), 1/8'' (stainless steel), 1/8''
(aluminum)
Included accessories:
Plasma torch
Power supply
Torch support
Sliding stop extension
Pipe plug
Wrench
3 Spare cathodes
5 Spare nozzles
3 Spare glass tubes
4 Spare O-rings
1 Spare cone washer 10gr liquid absorbing material
2 Spare springs
1 Spare 1mm drill bit
ITEM 45850-0VGA
$599.99
> At Harbor Frieght use "plasma" as a key word, it's about mid-pagefor $599
> also, another linkAt the Harbor Site... (below)
> http://home.ptt.ru/alplaz/Ge.htm
*****************
What boggles my mind is that this has popped up quietly. It is light
enough to Gantry Mount. Runs on the power of two hair dryers, and
puts out a beam slightly cooler than the surface of the sun.
It does not get into how precise the beam is - or how accurate the
cutter... But at $600 - it is worth checking out.
It plays into the Gantry Mount interchangeable ENM-Plasma cutter idea
very well.
** Harbor Product Post ****************
Cut, Weld and Braze With One Machine!
This portable unit uses water vapor to cut sheet metal, stainless
steel, aluminum and copper up to 1/8'' thick. Cuts cleaner, hotter,
faster with less damage to the surrounding area than gas cutting.
Continuous operation for 12-30 minutes
Inverter technology power supply
Spare parts kit
Specifications:
Input power: 220V, 10 amps, 60 Hz
Operating time on one filling: 15-18 min.
Maximum water consumption: 8.5 oz. per hr.
Jet flame temperature: 14,400° F (8000° C)
Cutting capacity: 1/16'' (steel), 1/8'' (stainless steel), 1/8''
(aluminum)
Included accessories:
Plasma torch
Power supply
Torch support
Sliding stop extension
Pipe plug
Wrench
3 Spare cathodes
5 Spare nozzles
3 Spare glass tubes
4 Spare O-rings
1 Spare cone washer 10gr liquid absorbing material
2 Spare springs
1 Spare 1mm drill bit
ITEM 45850-0VGA
$599.99
Discussion Thread
Mike Snodgrass
2003-01-12 10:06:50 UTC
water vapor plasma
Tim Goldstein
2003-01-12 10:09:07 UTC
RE: [CAD_CAM_EDM_DRO] water vapor plasma
James Cullins
2003-01-12 13:35:50 UTC
Re: [CAD_CAM_EDM_DRO] water vapor plasma
Mike Snodgrass
2003-01-12 14:21:48 UTC
Re: [CAD_CAM_EDM_DRO] water vapor plasma
Bob Simon
2003-01-12 14:26:36 UTC
RE: [CAD_CAM_EDM_DRO] water vapor plasma
turbulatordude <davemucha@j...
2003-01-12 14:39:02 UTC
Re: water vapor plasma
Mike Snodgrass
2003-01-12 14:59:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: water vapor plasma
turbulatordude <davemucha@j...
2003-01-12 15:37:11 UTC
Re: water vapor plasma
Randy Gordon-Gilmore
2003-01-12 17:44:38 UTC
RE: water vapor plasma
dvideohd <jrobinson46@c...
2003-01-13 01:09:20 UTC
Re: water vapor plasma
Mike Snodgrass
2003-01-13 05:10:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: water vapor plasma
turbulatordude <davemucha@j...
2003-01-13 06:01:20 UTC
Re: water vapor plasma
Jon Elson
2003-01-13 10:28:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: water vapor plasma