CAD CAM EDM DRO - Yahoo Group Archive

xylotec xfrmr was Re: Don't give up!!!

on 2003-01-31 08:45:43 UTC
John,

It really has gotten reasonable, hasn't it?...

One note, the Xylotec board may not like that 24voltAC transformer!

When rectified and filtered, it will likely put out about 34VDC; and
the limit for the chips used by Jeff is 35VDC. A bit close...

Better to find an 16-21 A/C volt xfrmr, for a max supply of 30VDC.
This is what Jeff recommends, voltage wise, for his xylotec boards.

Hope this helps,

Ballendo



--- In CAD_CAM_EDM_DRO@yahoogroups.com, "j.guenther"
<j.guenther@v...> wrote:
> Amen, and you can now get a very workable CNC conversion of a small
machine,
> for about $225.00 not including the machine. I have the plans for
Dave
> Rigotti's HobbyCNC machine and have seen one in action that someone
in the
> CAMS club built, pretty impressive for a plywood machine, and the
quality of
> the work he produces with it is outstanding. Below is my take on
just how
> low cost you can go for a basic beginner CNC conversion:
>
> Estimated Cost of a Basic CNC Conversion
>
> Supplier Part Number Price
> Xylotex Driver Board
> www.xylotex.com Xylotex XS-3525/8S-3 $85.00
>
> 24 Volt 10 Amp transformer
> www.mpja.com MPJA 7846 TR $17.99
>
> Bridge Rectifier
> www.mpja.com MPJA 5248BR $2.70
>
> 15000uf 100 V Electrolytic Cap
> www.mouser.com Mouser 539-CGS100V15000 $29.66
>
> 3ea 100 oz/in Stepper Motors e-bay $25.00
> Misc. wire, switches, connectors Radio Shack $40.00
>
> Electronic Parts: $200.35
>
> TurboCNC software www.dakeng.com DAK Eng. $20.00
>
> Total: $220.35
>
>
> Please note that this does not include shipping, motor mounts, motor
> couplers or a box to put the driver / power supply in. Depending
on the
> current levels you are using you may also need a fan for the driver
box. I
> did not include the cost of a surplus PC since this can vary
greatly. This
> also does not take into account what a person may already have in
their
> parts collection.
>
> John Guenther
> 'Ye Olde Pen Maker'
> Sterling, Virginia

Discussion Thread

Fusion X Studio 2003-01-29 11:19:30 UTC Small CNC Laser for Balsa gnrshelton <gnrshelton@y... 2003-01-29 12:08:06 UTC Re: Small CNC Laser for Balsa John Myjak <myjakjs@a... 2003-01-29 13:14:57 UTC Re: Small CNC Laser for Balsa Fusion X Studio 2003-01-29 16:00:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Small CNC Laser for Balsa Peter Seddon 2003-01-30 02:01:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Small CNC Laser for Balsa ballendo <ballendo@y... 2003-01-31 06:51:01 UTC Re: Small CNC Laser for Balsa C.S. Mo 2003-01-31 06:59:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Small CNC Laser for Balsa ballendo <ballendo@y... 2003-01-31 07:11:58 UTC Don't give up!!! wasRe: Small CNC Laser for Balsa Tim Goldstein 2003-01-31 07:46:00 UTC RE: [CAD_CAM_EDM_DRO] Don't give up!!! ballendo <ballendo@y... 2003-01-31 08:01:01 UTC Re: Don't give up!!! j.guenther 2003-01-31 08:24:14 UTC RE: [CAD_CAM_EDM_DRO] Don't give up!!! C.S. Mo 2003-01-31 08:30:51 UTC RE: [CAD_CAM_EDM_DRO] Don't give up!!! ballendo <ballendo@y... 2003-01-31 08:45:43 UTC xylotec xfrmr was Re: Don't give up!!! ballendo <ballendo@y... 2003-01-31 08:50:15 UTC Re: Don't give up!!! Jon Elson 2003-01-31 10:27:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Small CNC Laser for Balsa jeffalanp <xylotex@h... 2003-01-31 10:32:30 UTC Re: Don't give up!!! j.guenther 2003-01-31 10:53:33 UTC RE: [CAD_CAM_EDM_DRO] Re: Don't give up!!! Carol & Jerry Jankura 2003-01-31 13:29:29 UTC RE: [CAD_CAM_EDM_DRO] Don't give up!!!