RE: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Posted by
Tim Goldstein
on 2003-02-02 13:25:50 UTC
Do you have a second drive? How about another motor? Sounds like one of
the two parts is bad. I know it is low tech, but swap and replace may be
a faster way to figure it out. I know you mentioned other motors. What
happens when you use one of them?
Tim
[Denver, CO]
Sherline products at Deep Discount
Mach1 & DeskCNC with credit card ordering
www.KTMarketing.com/Sherline
the two parts is bad. I know it is low tech, but swap and replace may be
a faster way to figure it out. I know you mentioned other motors. What
happens when you use one of them?
Tim
[Denver, CO]
Sherline products at Deep Discount
Mach1 & DeskCNC with credit card ordering
www.KTMarketing.com/Sherline
> -----Original Message-----
> Yes I'm sure. It's regulated at 36 Volts and can deliver
> (tested) 9 Amps. At 9Amps the voltage is 35.9 ... it's solid
> supply. Hans W
Discussion Thread
Hans Wedemeyer
2003-02-01 14:15:12 UTC
Gecko G201 and Drive Current ?
Tim Goldstein
2003-02-01 14:21:00 UTC
RE: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-01 14:33:36 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-01 16:40:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?
Mariss Freimanis <mariss92705@y...
2003-02-01 18:23:29 UTC
Re: Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-01 19:11:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Mariss Freimanis <mariss92705@y...
2003-02-01 20:34:32 UTC
Re: Gecko G201 and Drive Current ?
Jon Elson
2003-02-01 22:56:45 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-02 02:24:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-02 03:10:28 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?
ballendo <ballendo@y...
2003-02-02 12:24:15 UTC
Re: Gecko G201 and Drive Current ?
Mariss Freimanis <mariss92705@y...
2003-02-02 13:08:54 UTC
Re: Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-02 13:20:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Hans Wedemeyer
2003-02-02 13:24:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Tim Goldstein
2003-02-02 13:25:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko G201 and Drive Current ?
Alan Marconett KM6VV
2003-02-02 15:20:43 UTC
Re: Gecko G201 and Drive Current ?
Mariss Freimanis <mariss92705@y...
2003-02-02 16:43:40 UTC
Re: Gecko G201 and Drive Current ?
Jon Elson
2003-02-02 21:54:12 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G201 and Drive Current ?