Re: stepper
Posted by
Jefferson H. Tomlinson <jeffersont@a...
on 2003-02-21 19:29:46 UTC
This is a two phase unipolar stepper motor.
term. 1 is phase "A" and term. 3 is phase "A NOT" with term. 6 going
to the current limiting resistor to the plus supply.
term. 4 is phase "B" and term. 5 is phase "B NOT" and term. 2 going
to the current limiting resistor to the plus supply.
I have worked with these type of stepper motors used in line printer
applications. The ones that I worked with were Slo-Syn model M061 and
M062 motors. The wiring for the larger M111, M112-FD, and M112-FJ
have screw terminals were the smaller one like I used have wire leads.
If the model numbers for the match the one of the number for the
larger stepper motors and are Slo-Syn I have the specs.
Jeff Tomlinson
term. 1 is phase "A" and term. 3 is phase "A NOT" with term. 6 going
to the current limiting resistor to the plus supply.
term. 4 is phase "B" and term. 5 is phase "B NOT" and term. 2 going
to the current limiting resistor to the plus supply.
I have worked with these type of stepper motors used in line printer
applications. The ones that I worked with were Slo-Syn model M061 and
M062 motors. The wiring for the larger M111, M112-FD, and M112-FJ
have screw terminals were the smaller one like I used have wire leads.
If the model numbers for the match the one of the number for the
larger stepper motors and are Slo-Syn I have the specs.
Jeff Tomlinson
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Gene <capper@i...> wrote:
> I have a nema 42 stepper motor and I was wondering if anyone can
make
> sense of the wiring. It has 6 terminal screws and with the O meter
set
> to 200 heres what I get.
> term.1 to term.3--1.9 ohms
> term.1 to term.6--1.3 ohms
> term.2 to term.4--1.3 ohms
> term.2 to term.5--1.3 ohms
> term.3 to term.1--1.9 ohms
> term.3 to term.6--1.3 ohms
> term.4 to term.5--1.9 ohms
> term.4 to term.2--1.3 ohms
> term.5 to term.2--1.3 ohms
> term.5 to term.4--1.9 ohms
> term.6 to term.3--1.3 ohms
> term.6 to term.1--1.3 ohms
>
> I am wondering which is the full coil and which is the half coil.
Discussion Thread
Gene
2002-07-25 22:40:10 UTC
stepper
Jon Elson
2002-07-26 21:43:59 UTC
Re: [CAD_CAM_EDM_DRO] stepper
Gene
2003-02-21 17:39:46 UTC
stepper
turbulatordude <davemucha@j...
2003-02-21 17:49:21 UTC
Re: stepper
Jefferson H. Tomlinson <jeffersont@a...
2003-02-21 19:29:46 UTC
Re: stepper
Gene
2003-02-22 12:56:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: stepper
Gene
2004-05-21 15:57:38 UTC
stepper
Roy J. Tellason
2004-05-21 16:23:19 UTC
Re: [CAD_CAM_EDM_DRO] stepper
Gene
2004-05-21 17:37:30 UTC
Re: [CAD_CAM_EDM_DRO] stepper
Roy J. Tellason
2004-05-21 18:02:22 UTC
Re: [CAD_CAM_EDM_DRO] stepper