CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Inexpensive oscilloscope?

Posted by Dan Mauch
on 2003-03-08 13:43:42 UTC
You really don't need a scope to set the dampening on the G320/G340. I
been setting them using a method that I described in earlier post on the
same subject. Just use a flywheel mounted on the shaft and the results
can be the same. You will probably need to check the archieves to find
it.
Dan
-----Original Message-----
From: Monte Westlund [mailto:montejw@...]
Sent: Friday, March 07, 2003 8:25 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Inexpensive oscilloscope?


Would one of these work for testing/tuning Gecko 320 drivers? They
look to have output to a computer such as a real oscilloscope does. A
couple down at the bottom of this page:
http://www.electronic-supply.com/DMM-page.htm

Monte


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill
List Mom List Owner



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Discussion Thread

Monte Westlund 2003-03-07 20:25:20 UTC Inexpensive oscilloscope? Jon Elson 2003-03-07 22:23:57 UTC Re: [CAD_CAM_EDM_DRO] Inexpensive oscilloscope? tony@j... 2003-03-07 22:54:29 UTC Re: Inexpensive oscilloscope? Monte Westlund 2003-03-07 23:04:25 UTC Re: Inexpensive oscilloscope? tony@j... 2003-03-07 23:07:48 UTC Re: Inexpensive oscilloscope? Keith Bowers 2003-03-08 13:07:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Inexpensive oscilloscope? Dan Mauch 2003-03-08 13:43:42 UTC RE: [CAD_CAM_EDM_DRO] Inexpensive oscilloscope? halle@t... 2003-03-08 13:53:48 UTC Re: [CAD_CAM_EDM_DRO] Inexpensive oscilloscope?