Re: I am looking for Lathe Cutting tool parameters for CNC
Posted by
Andrew Mawson
on 2003-05-19 15:03:41 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, glee@i... wrote:
The problem that you will have is that small machines like my Denford
ORAC and your Sherline don't have the power to run negative rake
inserts - and as most of industry is using negative rake tooling you
have a significantly reduced selection in positive rake. There are
some negative rake inserts that have a chip breaker groove that
presents a 'quasi positive' rake angle - maybe that's the sort of
thing that you should look for.
No point in my suggesting suppliers to you as you are the wrong side
of the big pond !
Andrew Mawson
Bromley, Kent, UK
>you
> David wrote:
>
> > By the way I highly reccomend that you consider tooling that uses
> > inserts. On a lathe these can be very economical and the data
> > need is easly obtained. Inserts are less that $4 a piece, on achange
> > triangular insert that is three cutting surfaces for a buck and
> each.particular
>
> Thanks, Dave.
>
> I believe that when you go this route, you are committing to a
> family of inserts.small CNC
>
> Do you have any favorite recommendations for insert tooling for a
> lathe like a Sherline that uses 1/4" square shank tools?Eric,
>
> Thaks,
>
> Eric
The problem that you will have is that small machines like my Denford
ORAC and your Sherline don't have the power to run negative rake
inserts - and as most of industry is using negative rake tooling you
have a significantly reduced selection in positive rake. There are
some negative rake inserts that have a chip breaker groove that
presents a 'quasi positive' rake angle - maybe that's the sort of
thing that you should look for.
No point in my suggesting suppliers to you as you are the wrong side
of the big pond !
Andrew Mawson
Bromley, Kent, UK
Discussion Thread
gglines1
2003-05-17 06:44:07 UTC
Newbie: Machining an oval?
turbulatordude
2003-05-17 07:24:43 UTC
Re: Newbie: Machining an oval?
ccq@x...
2003-05-17 08:37:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Machining an oval?
Indy123456
2003-05-17 15:15:04 UTC
Re: Newbie: Machining an oval?
Raymond Heckert
2003-05-17 16:17:47 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Machining an oval?
gglines1
2003-05-17 16:34:31 UTC
Re: Newbie: Machining an oval?
gglines1
2003-05-17 16:36:26 UTC
Re: Newbie: Machining an oval?
gglines1
2003-05-17 16:38:21 UTC
Re: Newbie: Machining an oval?
gglines1
2003-05-17 16:46:00 UTC
Re: Newbie: Machining an oval?
turbulatordude
2003-05-17 16:49:25 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
turbulatordude
2003-05-17 17:09:26 UTC
Re: Newbie: Machining an oval?
gglines1
2003-05-17 20:17:13 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
turbulatordude
2003-05-17 21:40:02 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
Raymond Heckert
2003-05-18 16:23:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Machining an oval?
glee@i...
2003-05-18 17:01:14 UTC
I am looking for Lathe Cutting tool parameters for CNC
gglines1
2003-05-18 23:40:35 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
Indy123456
2003-05-19 00:31:26 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
glee@i...
2003-05-19 09:53:14 UTC
Re: I am looking for Lathe Cutting tool parameters for CNC
Andrew Mawson
2003-05-19 10:13:18 UTC
Re: I am looking for Lathe Cutting tool parameters for CNC
glee@i...
2003-05-19 10:25:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
David A. Frantz
2003-05-19 10:35:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
glee@i...
2003-05-19 10:42:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
gglines1
2003-05-19 13:35:41 UTC
What is an Oval ? ( was Re: Newbie: Machining an oval?
Andrew Mawson
2003-05-19 15:03:41 UTC
Re: I am looking for Lathe Cutting tool parameters for CNC
doug98105
2003-05-19 17:42:43 UTC
Re: I am looking for Lathe Cutting tool parameters for CNC
Jon Elson
2003-05-19 22:30:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
glee@i...
2003-05-21 21:51:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
glee@i...
2003-05-22 00:25:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: I am looking for Lathe Cutting tool parameters for CNC
glee@i...
2003-05-22 21:01:24 UTC
CAD/CAM Tutorial posted on my web site: