Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Posted by
Harvey White
on 2003-05-24 20:02:37 UTC
On Sat, 24 May 2003 18:09:38 -0400, you wrote:
tricky, I think.
your blocks (while laid side by side) will be as big as the miter saw
can cut.
I'd suggest a production stop for the saw so that everything comes out
the same size. It'll make life easier for you.
Harvey
>OK, sounds reasonable. Z direction you will find to be a bit more
>----- Original Message -----
>From: Harvey White <madyn@...>
>To: <CAD_CAM_EDM_DRO@yahoogroups.com>
>Sent: Friday, May 23, 2003 9:51 PM
>Subject: Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
>
>this X-Y table will manipulate peace of metal 6" x 18" x 1/8" in X-Y plane.
>If it comes to worst, I can just add couple more bearings which would work
>in Z
>direction - not as pretty as what you did...
tricky, I think.
>Actually, you could do the job with a miter saw, it's just that all
>> >> I absolutely would recommend that you use a good and well aligned
>> >> table saw for this, however.
>> >
>> >Yes, I have a brand new miter saw, currently under the table, waiting
>when
>> >its star
>> >will come up.
>>
>> Unless you have a very "long" miter saw, you will see that it only
>> cuts about 8 to 10 inches at the max. For making a long and angled
>> board, this presents a few difficulties.
>
>Well, since I only got a miter saw, I will use blocks for support - not
>over the whole length of the guide but at a few spots alongside it.
>I just hope it will work as well...
your blocks (while laid side by side) will be as big as the miter saw
can cut.
I'd suggest a production stop for the saw so that everything comes out
the same size. It'll make life easier for you.
Harvey
>
>>
>> H.
>Best regards, Alex
Discussion Thread
Alan Marconett KM6VV
2000-10-12 11:25:55 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
ballendo@y...
2000-10-27 16:06:28 UTC
re: New file uploaded to CAD_CAM_EDM_DRO
Smoke
2000-10-27 16:23:00 UTC
Re: [CAD_CAM_EDM_DRO] re: New file uploaded to CAD_CAM_EDM_DRO
ballendo@y...
2000-10-27 20:04:35 UTC
Re: re: New file uploaded to CAD_CAM_EDM_DRO
Smoke
2000-10-27 21:37:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: re: New file uploaded to CAD_CAM_EDM_DRO
Smoke
2000-11-12 15:07:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: New file uploaded to CAD_CAM_EDM_DRO
Alan Marconett KM6VV
2001-05-23 20:09:14 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
JanRwl@A...
2001-05-23 20:36:43 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Alan Marconett KM6VV
2001-05-23 21:55:13 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
JanRwl@A...
2003-01-07 15:18:31 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Lloyd Leung
2003-01-08 10:39:09 UTC
RE: New file uploaded to CAD_CAM_EDM_DRO
alex
2003-05-23 10:29:56 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Harvey White
2003-05-23 18:43:02 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
alex
2003-05-24 15:47:36 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Harvey White
2003-05-24 20:02:37 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
alex
2003-05-25 12:00:45 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
JanRwl@A...
2003-08-09 19:28:24 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
JanRwl@A...
2003-09-01 17:22:50 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO
Jon Elson
2003-09-01 22:19:46 UTC
Re: [CAD_CAM_EDM_DRO] New file uploaded to CAD_CAM_EDM_DRO