RE: [CAD_CAM_EDM_DRO] Machining Ball Screws
Posted by
Larry Ragan
on 2003-06-04 10:04:54 UTC
I used carbid insert and turned at a slow speed. Took several light
cuts. When I got it down below the threaded part, I made a mild steel
sleeve that went over this and did a press fit onto it. I then turned
the mild steel part to the diameter needed for bearings.
cuts. When I got it down below the threaded part, I made a mild steel
sleeve that went over this and did a press fit onto it. I then turned
the mild steel part to the diameter needed for bearings.
Discussion Thread
Graham Stabler
2003-06-04 06:37:12 UTC
Building a small 4th axis
stevenson_engineers
2003-06-04 06:56:01 UTC
Re: Building a small 4th axis
Graham Stabler
2003-06-04 07:05:23 UTC
Re: Building a small 4th axis
Tony Jeffree
2003-06-04 07:20:15 UTC
Re: [CAD_CAM_EDM_DRO] Building a small 4th axis
turbulatordude
2003-06-04 08:01:26 UTC
Re: Building a small 4th axis
Tony Jeffree
2003-06-04 08:30:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Building a small 4th axis
Steven Ciciora
2003-06-04 08:37:03 UTC
Machining Ball Screws
wanliker@a...
2003-06-04 09:29:47 UTC
Building a small 4th axis
Graham Stabler
2003-06-04 10:03:07 UTC
Re: Building a small 4th axis
Larry Ragan
2003-06-04 10:04:54 UTC
RE: [CAD_CAM_EDM_DRO] Machining Ball Screws
Paul
2003-06-04 10:27:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Building a small 4th axis
Paul
2003-06-04 10:27:52 UTC
Re: [CAD_CAM_EDM_DRO] Machining Ball Screws
turbulatordude
2003-06-04 10:35:22 UTC
Re: Machining Ball Screws
Tony Jeffree
2003-06-04 10:47:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Building a small 4th axis
Indy123456
2003-06-04 11:07:40 UTC
Re: Machining Ball Screws
stevenson_engineers
2003-06-04 11:10:21 UTC
Re: Building a small 4th axis
Alan Marconett KM6VV
2003-06-04 11:16:43 UTC
Re: [CAD_CAM_EDM_DRO] Building a small 4th axis
Tony Jeffree
2003-06-04 11:25:43 UTC
Re: [CAD_CAM_EDM_DRO] Building a small 4th axis
Alan Marconett KM6VV
2003-06-04 11:59:20 UTC
Re: [CAD_CAM_EDM_DRO] Building a small 4th axis
Tony Jeffree
2003-06-04 12:04:20 UTC
Re: [CAD_CAM_EDM_DRO] Building a small 4th axis
mayfieldtm
2003-06-04 12:23:37 UTC
Re: Machining Ball Screws
Steven Ciciora
2003-06-04 12:48:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Machining Ball Screws
Dan Mauch
2003-06-04 13:41:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Machining Ball Screws
Torsten
2003-06-05 07:12:53 UTC
Re: Machining Ball Screws
Larry Nicks
2003-06-05 18:34:03 UTC
Re: Machining Ball Screws