CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Dan's product announcement

Posted by Dan Mauch
on 2000-03-11 06:09:39 UTC
Yes the pot provides the speed control of the pulses to the drivers.
Dan
-----Original Message-----
From: Marshall Pharoah <m_pharoah@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Friday, March 10, 2000 1:05 PM
Subject: Re: [CAD_CAM_EDM_DRO] Dan's product announcement


>From: "Marshall Pharoah" <m_pharoah@...>
>
>Dan,
>
>You're starting to get me interested. I didn't pay a lot of attention to
your
>previous post. Are you using a pot to control speed in the power feed
mode?
>
>When you connect this to a PC, are you using the parallel port?
>I've been doing some work with digital I/O port boards from National, and
I'd be more
>interested in using them, think it would be any problem?
>
>Marshall
>
>----- Original Message -----
>From: Dan Mauch <dmauch@...>
>To: <CAD_CAM_EDM_DRO@onelist.com>
>Sent: Friday, March 10, 2000 3:51 PM
>Subject: Re: [CAD_CAM_EDM_DRO] Dan's product announcement
>
>
>> As per the power feed I added the pulse generator to the 5A board for two
>> reasons. One for testing and the other for a power feed.
>> It is really quite simple. I used a three pole three position rotary
>> switch. The pulse line went to the pole and the X-Y-Z step pins were
>> connected to the the approiate connections. A dir ground connection was
>> soldered to a second pole. The x-y-z direction line were connected to
the
>> appropriate connections on the switch. When in the power feed mode the
db25
>> cable was disconnected. But I used an AB switch for that problem.
>> There was a SPDT switch that selected manual Power feed or computer. A
>> another SPST switch was in the direction line. With switch A in the
manual
>> mode the pulse generator feed the rotary switch which in turn provided
the
>> signals to the step lines. Flip the direction switch and the manual
>> direction would flip.
>> I'll see if I can draw it up soon.
>> Dan
>>
>> --
>>
>>
>
>
>------------------------------------------------------------------------
>GET A NEXTCARD VISA, in 30 seconds! Get rates as low as 2.9%
>Intro or 9.9% Fixed APR and no hidden fees. Apply NOW!
>http://click.egroups.com/1/936/1/_/423600/_/952722383/
>------------------------------------------------------------------------
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>For the FAQ, go to http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>

Discussion Thread

Dan Mauch 2000-03-10 12:51:51 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement Marshall Pharoah 2000-03-10 13:07:29 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement wanliker@a... 2000-03-10 14:16:43 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement Tim Goldstein 2000-03-10 14:30:47 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement Dan Mauch 2000-03-11 06:09:39 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement Dan Mauch 2000-03-11 06:15:30 UTC Re: [CAD_CAM_EDM_DRO] Dan's product announcement