Re: [CAD_CAM_EDM_DRO] Re: Cutting an arc help G2/G3?

----- Original Message -----
From: "John D. Guenther" <j.guenther@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, June 25, 2003 11:34 AM
Subject: [CAD_CAM_EDM_DRO] Re: Cutting an arc help G2/G3?


> George,
>
> Sorry for not responding to this sooner. The radius of a 12" circle
> is 6", the radius of an 11" circle is 5.5", so the difference would
> give you a part 1/2" wide. Using a radius of 5" for the inner arc
> will give you a part 1" wide.
>
> I just saw your message about using a 3/4" endmill, I will redo the
> g-code this evening and post it in place of what I put up last night.
> I am at work now and don't have all the proper software tools on my
> laptop to get it done for you here. Sorry for the delay, I should
> have read my email when I got up this morning.
>
> John Guenther
> Sterling, Virginia
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "gglines1" <gglines@c...>
> wrote:
> > If the outer edge of the ring is 12" and the part is 1" wide,
> > wouldn't the inner edge of the ring be an 11" circle?
> >
> > George
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "John Guenther"
> > <j.guenther@v...> wrote:
> > > George,
> > >
> > > By the way, if "2.5" long piece cut out of a 12" ring that is 1"
> > wide" is
> > > true, then you are talking about a 12" circle and a 10" circle if
> > the part
> > > really is 1" wide.
> > >
> > > John Guenther
> > > 'Ye Olde Pen Maker'
> > > Sterling, Virginia
> > >
> > > > -----Original Message-----
> > > > From: gglines1 [mailto:gglines@c...]
> > > > Sent: Tuesday, June 24, 2003 14:55 PM
> > > > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > Subject: [CAD_CAM_EDM_DRO] Cutting an arc help G2/G3?
> > > >
> > > >
> > > > I have to cut a small workpiece with a curve. The workpiece
> > will be
> > > > 2.5 inches long, 1" wide and 1/2" thick. The long end of the
> > > > rectangle needs to be cut in an arc to match a 12" circle, the
> > > > shorter inside arc to match an 11" circle. Hard to describe,
> > think
> > > > of a 2.5" long piece cut out of a 12" ring that is 1" wide.
> > > >
> > > > Assuming I start with a workpiece that is a rectange 2.5" long
> > by 1"
> > > > wide, how would I program the arc cut? I can see programming a
> > > > circle and letting the machine make a 12" revolution, but that
> > would
> > > > be really slow. I'm not sure how to program just the part of
> > the arc
> > > > that I need.
> > > >
> > > > Thanks,
> > > >
> > > > George
> > > >
> > > >
> > > >
> > > > (FYI: My controller software (Microkinetics Millmaster Pro)
> > > > recognizes I and J parameters but not the R parameter with
> G2/G3)
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > >
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > > > wanliker@a..., timg@k...
> > > > Moderator: pentam@c... indigo_red@q... [Moderators]
> > > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > > > reach it if you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider this
> > > > to be a sister site to the CCED group, as many of the same
> > > > members are there, for OT subjects, that are not allowed on the
> > CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > > > POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > > > EXCEPTIONS........
> > > > bill
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > >
> > > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > > >
> > > >
> > > >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>