Re: Proper solid state relay to use for spindle control
Posted by
mrgamber
on 2003-06-25 13:08:55 UTC
No, they are Solid State. No opto isolation, but would interface to a
controller board that is isolated.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
<KM6VV@a...> wrote:
controller board that is isolated.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
<KM6VV@a...> wrote:
> Hi Alex, mrgamber,120VAC ...
>
> I like to use:
>
> Crydom Solid State switches, input 3-32 V, output 25A with
>SS.
> http://www.crydom.com/product/ssrindex.asp
>
> The Axxus dual relay board has RELAYS on it, I don't think they're
>spindle
>
> Alan KM6VV
>
>
> alex wrote:
> >
> > Is this board optoisolated?
> > Alex
> > ----- Original Message -----
> > From: mrgamber <mgamber@c...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Wednesday, June 25, 2003 2:45 PM
> > Subject: [CAD_CAM_EDM_DRO] Proper solid state relay to use for
> > controlrelays.
> >
> > > The following offers a very nice package of two solid state
> > > http://members.shaw.ca/axxus/db1v20.htmmounted
> > >
> > > I have been looking through catalogs and notice that non-pcb
> > > relays cost ~$25 for 1. The relays on the above PCB cost ~$1.50each.
> > >solenoid) and
> > > I have intentions of using these for Spindle, Mist (AC
> > > to turn off the power supply to my Gecko drivers.HP
> > >
> > > Question: Are the relays on this PCB appropriate for this use?
> > >
> > > Spindle motor is a (TAIG) 1/10 HP AC, but I may upgrade to 1/4
> > >
Discussion Thread
mrgamber
2003-06-25 11:45:47 UTC
Proper solid state relay to use for spindle control
alex
2003-06-25 12:15:47 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
Alan Marconett KM6VV
2003-06-25 12:34:43 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
mrgamber
2003-06-25 13:08:55 UTC
Re: Proper solid state relay to use for spindle control
Vajk Fekete
2003-06-25 13:17:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
mrgamber
2003-06-25 13:28:09 UTC
Re: Proper solid state relay to use for spindle control
JanRwl@A...
2003-06-25 14:42:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
Chris Baugher
2003-06-25 14:50:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
John Guenther
2003-06-25 15:10:31 UTC
RE: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
alex
2003-06-25 18:33:32 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
Alan Marconett KM6VV
2003-06-25 18:49:55 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
mrgamber
2003-06-25 19:26:53 UTC
Re: Proper solid state relay to use for spindle control