Re: Proper solid state relay to use for spindle control
Posted by
mrgamber
on 2003-06-25 19:26:53 UTC
allied elec sells the relay's only for $1.50.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "John Guenther"
<j.guenther@v...> wrote:
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "John Guenther"
<j.guenther@v...> wrote:
> That should work, 120 volts at 12 amps is quite a lot to switch butthey say
> the relays on the relay board are rated at that. However you seemto be a
> little off on your pricing, the relay board is $25.00 which makesthe relays
> about $12.50 each.spindle
>
> John Guenther
> 'Ye Olde Pen Maker'
> Sterling, Virginia
>
> > -----Original Message-----
> > From: mrgamber [mailto:mgamber@c...]
> > Sent: Wednesday, June 25, 2003 14:46 PM
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: [CAD_CAM_EDM_DRO] Proper solid state relay to use for
> > controlrelays.
> >
> >
> > The following offers a very nice package of two solid state
> > http://members.shaw.ca/axxus/db1v20.htmmounted
> >
> > I have been looking through catalogs and notice that non-pcb
> > relays cost ~$25 for 1. The relays on the above PCB cost ~$1.50each.
> >and
> > I have intentions of using these for Spindle, Mist (AC solenoid)
> > to turn off the power supply to my Gecko drivers.CCED list.
> >
> > Question: Are the relays on this PCB appropriate for this use?
> >
> > Spindle motor is a (TAIG) 1/10 HP AC, but I may upgrade to 1/4 HP
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > wanliker@a..., timg@k...
> > Moderator: pentam@c... indigo_red@q... [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
> > to be a sister site to the CCED group, as many of the same
> > members are there, for OT subjects, that are not allowed on the
> >http://docs.yahoo.com/info/terms/
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
> >
> >
> >
Discussion Thread
mrgamber
2003-06-25 11:45:47 UTC
Proper solid state relay to use for spindle control
alex
2003-06-25 12:15:47 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
Alan Marconett KM6VV
2003-06-25 12:34:43 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
mrgamber
2003-06-25 13:08:55 UTC
Re: Proper solid state relay to use for spindle control
Vajk Fekete
2003-06-25 13:17:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
mrgamber
2003-06-25 13:28:09 UTC
Re: Proper solid state relay to use for spindle control
JanRwl@A...
2003-06-25 14:42:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
Chris Baugher
2003-06-25 14:50:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Proper solid state relay to use for spindle control
John Guenther
2003-06-25 15:10:31 UTC
RE: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
alex
2003-06-25 18:33:32 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
Alan Marconett KM6VV
2003-06-25 18:49:55 UTC
Re: [CAD_CAM_EDM_DRO] Proper solid state relay to use for spindle control
mrgamber
2003-06-25 19:26:53 UTC
Re: Proper solid state relay to use for spindle control