CAD CAM EDM DRO - Yahoo Group Archive

Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops)

Posted by caudlet
on 2003-08-26 11:08:11 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, cruiser man <crusier_32@y...>
wrote:
> Sorry about the double post here, I accidentaly hit
> send before I was done. Please disregard my first
> post.
>
> I think that the system that you are using has some
> very strong merits for most people. Eventually I will
> probably go that route or something similar. I have
> two problems with it though.
>
> 1. I can't control a oxy/acetylene torch with
> this system. Which probably is not a very big deal,
> though I would like the ability to cut larger pieces
> of steal then what plasma will pierce. Ideally I
> would like to have the ability to cut some thick
> chunks of steal up to say six inches. Obviously I
> will need to make multiple passes no matter what I cut
> with.
> 2. Second and not so important I have to use
> Windows to run the system. I have no problem with
> Windows, it just is not my preferred choice.
>
> Will
>
>


I can't think of anyway to control an oxy cutting torch other than
the obvious mechanical. It's difficult to sense height with
electronics when there is a 10,000 deg flame a few inches away and
molten metal is involved! The 6 inch stuff will be a challenge. The
abrasive water jet guys can do that in all kinds of material. There
is a waterjet group that I slide by once in a while.

Discussion Thread

cruiser man 2003-08-22 19:11:03 UTC Newbi needs advise on torch table. caudlet 2003-08-23 07:32:02 UTC Re: Newbi needs advise on torch table. turbulatordude 2003-08-23 08:11:50 UTC Re: Newbi needs advise on torch table. cruiser man 2003-08-23 16:59:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. turbulatordude 2003-08-23 17:24:35 UTC Re: Newbi needs advise on torch table. Paul 2003-08-23 17:47:18 UTC Re: [CAD_CAM_EDM_DRO] Newbi needs advise on torch table. caudlet 2003-08-23 19:33:23 UTC Re: Newbi needs advise on torch table. turbulatordude 2003-08-24 07:36:17 UTC Re: Newbi needs advise on torch table. - now THC caudlet 2003-08-25 16:08:27 UTC Re: Newbi needs advise on torch table. - now THC cruiser man 2003-08-26 07:46:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC cruiser man 2003-08-26 07:58:05 UTC Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops) caudlet 2003-08-26 11:03:53 UTC Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops) caudlet 2003-08-26 11:08:11 UTC Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops) turbulatordude 2003-08-26 11:13:52 UTC Re: Newbi needs advise on torch table. - now THC David Paulson 2003-08-26 11:32:18 UTC RE: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC