RE: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC
Posted by
David Paulson
on 2003-08-26 11:32:18 UTC
To cut 6" all that it required is the correct tip to be installed. You do
not speed up and slow down. In fact, steel to 24" can be cut with a torch.
Rutex has a torch height control for an oxy acet setup. It looks as if it
uses a proximity to sense cutting height.
http://www.rutex.com/home/flame.html
-----Original Message-----
From: turbulatordude [mailto:davemucha@...]
Sent: Tuesday, August 26, 2003 12:13 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now
THC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, cruiser man <crusier_32@y...>
wrote:
think you might need some manual control like a pot to adjust the
feed rate so as you monitor the cutting, you can speed up or slow
down the feed rates.
And for that, I'm not sure what software can accept an external
sensor.
Dave
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
not speed up and slow down. In fact, steel to 24" can be cut with a torch.
Rutex has a torch height control for an oxy acet setup. It looks as if it
uses a proximity to sense cutting height.
http://www.rutex.com/home/flame.html
-----Original Message-----
From: turbulatordude [mailto:davemucha@...]
Sent: Tuesday, August 26, 2003 12:13 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now
THC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, cruiser man <crusier_32@y...>
wrote:
> I think that the system that you are using has someIf you are torch cutting, you do it all in one pass. for that I
> very strong merits for most people. Eventually I will
> prbably go that route or something simialiar. I have
> two problems with it though.
>
> 1. I can't controll a oxy/acetylne torch with
> this system. Which probably is not a very big deal,
> though I would like the ablity to cut larger pices of
> steal then what plasma will pirce. Ideally I would
> like to have the ablity to gut some varly thick lumps
> of steal up to say six inches. Obvously I will need
> to make multible passes no matter what I cut with.
think you might need some manual control like a pot to adjust the
feed rate so as you monitor the cutting, you can speed up or slow
down the feed rates.
And for that, I'm not sure what software can accept an external
sensor.
Dave
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
cruiser man
2003-08-22 19:11:03 UTC
Newbi needs advise on torch table.
caudlet
2003-08-23 07:32:02 UTC
Re: Newbi needs advise on torch table.
turbulatordude
2003-08-23 08:11:50 UTC
Re: Newbi needs advise on torch table.
cruiser man
2003-08-23 16:59:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table.
turbulatordude
2003-08-23 17:24:35 UTC
Re: Newbi needs advise on torch table.
Paul
2003-08-23 17:47:18 UTC
Re: [CAD_CAM_EDM_DRO] Newbi needs advise on torch table.
caudlet
2003-08-23 19:33:23 UTC
Re: Newbi needs advise on torch table.
turbulatordude
2003-08-24 07:36:17 UTC
Re: Newbi needs advise on torch table. - now THC
caudlet
2003-08-25 16:08:27 UTC
Re: Newbi needs advise on torch table. - now THC
cruiser man
2003-08-26 07:46:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC
cruiser man
2003-08-26 07:58:05 UTC
Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops)
caudlet
2003-08-26 11:03:53 UTC
Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops)
caudlet
2003-08-26 11:08:11 UTC
Re:[CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC(oops)
turbulatordude
2003-08-26 11:13:52 UTC
Re: Newbi needs advise on torch table. - now THC
David Paulson
2003-08-26 11:32:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Newbi needs advise on torch table. - now THC