Re: [CAD_CAM_EDM_DRO] Servo Amps $75

There wasn't enough infomation in the ad to determine that but it sounded
like it could take step and direction inputs.
Dan

-----Original Message-----
From: Mike Gann <mikegann@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Thursday, March 23, 2000 9:23 AM
Subject: Re: [CAD_CAM_EDM_DRO] Servo Amps $75

>From: Mike Gann <mikegann@...>
>
>But back to the original question -
>
>If they were available, would this be adequate for CNC and what size of
>Mill for example could this size of amp drive?
>
>Mike
>
>Dan Mauch wrote:
>>
>> From: "Dan Mauch" <dmauch@...>
>>
>> I saw that ad too and called them. They first said they were out of them

but

>> decided to do a check. They are not yet available was the second answer.
>> Dan
>> -----Original Message-----
>> From: Roger Brower <rbrower@...>
>> To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
>> Date: Thursday, March 23, 2000 7:38 AM
>> Subject: [CAD_CAM_EDM_DRO] Servo Amps $75
>>
>> >From: Roger Brower <rbrower@...>
>> >
>> >Front page of H&R flyer, 5 amp 24 volt
>> >servo motor control board, $75 Is this
>> >the type ot thing for CNC?
>> >
>> >
>> >------------------------------------------------------------------------
>> >GET A NEXTCARD VISA, in 30 seconds! Get rates as low as 0.0%
>> >Intro or 9.9% Fixed APR and no hidden fees. Apply NOW!
>> >http://click.egroups.com/1/937/2/_/423600/_/953825899/
>> >------------------------------------------------------------------------
>> >
>> >Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>> discussion of shop built systems in the above catagories.
>> >To Unsubscribe, read archives, change to or from digest.
>> >Go to: http://www.onelist.com/isregistered.cgi
>> >Log on, and you will go to Member Center, and you can make changes

there.

>> >For the FAQ, go to http://www.ktmarketing.com/faq.html
>> >bill,
>> >List Manager
>> >
>> >
>>
>> ------------------------------------------------------------------------
>> PERFORM CPR ON YOUR APR!
>> Get a NextCard Visa, in 30 seconds! Get rates as low as
>> 0.0% Intro or 9.9% Fixed APR and no hidden fees.
>> Apply NOW!
>> http://click.egroups.com/1/2121/2/_/423600/_/953830315/
>> ------------------------------------------------------------------------
>>
>> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the

discussion of shop built systems in the above catagories.

>> To Unsubscribe, read archives, change to or from digest.
>> Go to: http://www.onelist.com/isregistered.cgi
>> Log on, and you will go to Member Center, and you can make changes there.
>> For the FAQ, go to http://www.ktmarketing.com/faq.html
>> bill,
>> List Manager
>
>------------------------------------------------------------------------
>MAXIMIZE YOUR CARD, MINIMIZE YOUR RATE!
>Get a NextCard Visa, in 30 seconds! Get rates as low as
>0.0% Intro or 9.9% Fixed APR and no hidden fees.
>Apply NOW!
>http://click.egroups.com/1/2122/2/_/423600/_/953832206/
>------------------------------------------------------------------------
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the

discussion of shop built systems in the above catagories.

>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>For the FAQ, go to http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>