RE: [CAD_CAM_EDM_DRO] Inverse of G-code

bill, what software are you running? can you tell it that z- is up? with
some careful planning, it'd be the easiest way to do that...


Erie Patsellis
Shelbyville Design & signworks
217-774-4444
signworks@... <mailto:signworks@...>

<mailto:signworks@cond>

Visit our website at: http://www.shelbyvilledesign.com



-----Original Message-----
From: W. P. McGown [mailto:bmcgown@...]
Sent: Thursday, September 18, 2003 12:23 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Inverse of G-code


I have a Gcode file that makes a negative image for a die/mold that I have
used to cast some ceramic tiles from. Now I would like to make these same
forms in copper by using a press. No problem on making the negative die but
the positive one is going to be a bit of trouble if I have to code the thing
by hand.

Does anyone know of software or a technique that could be used to "invert"
the G-code?

Many thanks in advance.

Bill

"If nobody makes you do it, it counts as fun"-Hobbes

----- Original Message -----
From: "Jon Elson" <elson@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, September 18, 2003 10:25 AM
Subject: Re: [CAD_CAM_EDM_DRO] Servo motor question


>
>
> Mina Aboul Saad wrote:
>
> >Hi group,
> >
> >I'm trying to do this for the first time, I'm planning to change the old
> >Fanuc controller on a German lathe, with a new one.
> >Servo motors are Siemens with the following specs:
> >- Dc Servo, permenant magnet.
> >- 1.03 KW
> >- 2000 RPM
> >- 176 V
> >- 7.1 A
> >- Max. torque 5 Nm
> >With an optical encoder, +5v and 1024 count/turn.
> >
> >I was thinking of using Turbocnc with Gecko drivers.
> >
> >Will this setup work?
> >
> There's one big Uh-Oh! That is the motor's 2000 RPM at 176 V.
> That means you will only get 1000 RPM at 80 V, the limit for the
> Gecko. You can figure out how this will affect your feedrates,
> and then decide whether to go ahead, swap motors, or whatever.
> Rutex has a higher voltage servo driver. See
> http://www.rutex.com/home/index.html for info on their products.
>
> >What is the required DC supply I need to build?
> >
> It should be no more than about 76 V for a Gecko drive.
>
> >Which Geckos to use G320 or G340, and what is the differnce between them.
> >
> >
> The G340 has a step pulse multiplier. This is useful if the servo motor
has
> a high resolution encoder, and the computer is very limited in the step
> pulses per second it can produce. Your motors have 256 cycle/rev encoders

> that produce 1024 quadrature counts, if I read your data right. At 2000
> RPM, that will produce 2000 * 1024 = 2,048,000 counts/min, or 34,133
> counts/second. If your computer can produce 34000 steps/second, you
> don't need the G340. And, using the step muliplier reduces the resolution
> of the servo. But, the voltage problem is the big one.
>
> Jon
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/