Re: [CAD_CAM_EDM_DRO] Re: Cheap drivers - special offer from Phytron.de

Read the spec carefully - they are actually 4.5A/phase max (i.e., 9A
total), not 9A/phase. You can set currents up to 3.5A, and then apply the
30% "boost" feature to get to 4.5a.

Regards,
Tony

At 12:21 13/11/2003 +0000, you wrote:

>The drive is the ZMX model. The offer is on their home page
>http://www.phytron.de/
>
> The data sheet is here
>http://www.phytron.de/home/pdf/zmx03-1d.pdf
>Unfortunately all the details are in German but you can piece together the
>information you need. They are up to 20 microstep, 0.75 to 9A at 80V max.
>They are standard step+direction drivers so they will work fine with
>TurboCNC.
>
>Phytron are not geared up to private sales to you have to send them a cheque
>or do a bank transfer. Either way they only accept Euros. I am in the
>process of trying to buy three so hopefully I will be able to tell you what
>they are like in the near future.
>
>Les
>
>----- Original Message -----
>From: "ajv2803959" <antonio_ximenez@...>
>To: <CAD_CAM_EDM_DRO@yahoogroups.com>
>Sent: Thursday, November 13, 2003 12:08 PM
>Subject: [CAD_CAM_EDM_DRO] Re: Cheap drivers - special offer from Phytron.de
>
>
>Hi, I don´t see the offer announce in the web, so I have been
>navigating in phytron web and I have question
>
>Is the model in offer GCD 93-70 ?
>Is it possible to use this model with step and direction signal ?
>Can I use TurboCnC with this drivers ?
>
>If I can use only serial port what software is suitable for control.
>Support for Gcodes.
>
>
>Thanks in advance
>
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
>timg@...
>Moderator: pentam@... indigo_red@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects
>goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to
>reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>sister site to the CCED group, as many of the same members are there, for
>OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
>THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Regards,
Tony