loking for help with power supply for rutex drives...
Posted by
keith
on 2003-12-11 09:26:42 UTC
i want to build or buy a power supply for rutex drives. i want to
use three of them to power three 3/4 hp micro 100 dc brush servo
motors on my old knee mill.
i'm not sure which drive are best fitted to my motors, but i'm
leaning towards the R90H (200V/40A). there are two other sizes
available that i can use if i can find the right power supply for
them. R990H2 (200V/10A) or R990H (100V/20A)
if i'm to build one,i need help to select the appropriate components,
as i am a machinist, and not an engineer. can anyone reccomend which
components i would need and where to find them? what va rating for
the transformer? what type of rectifier? what kind of capacitor or
filter? any schematics for this?
or can anyone possibly reccomend where i can buy a power supply?...
just got the motors, can't wait to get this up and running!
my motor info is as follows:
Nema 42 Face mount with 5/8" output shaft
micro 100 reliance electric
model no e723
serial no g000046
date code 2597
revision b
part no 0723-03-049 A
ccustomer part no 3/4 H.P. PWM
encoder #s heds-5605 A06 0333 A
regards,
keith
use three of them to power three 3/4 hp micro 100 dc brush servo
motors on my old knee mill.
i'm not sure which drive are best fitted to my motors, but i'm
leaning towards the R90H (200V/40A). there are two other sizes
available that i can use if i can find the right power supply for
them. R990H2 (200V/10A) or R990H (100V/20A)
if i'm to build one,i need help to select the appropriate components,
as i am a machinist, and not an engineer. can anyone reccomend which
components i would need and where to find them? what va rating for
the transformer? what type of rectifier? what kind of capacitor or
filter? any schematics for this?
or can anyone possibly reccomend where i can buy a power supply?...
just got the motors, can't wait to get this up and running!
my motor info is as follows:
Nema 42 Face mount with 5/8" output shaft
> 120 Volt Nominal Terminal Voltage Ratingload
> Torque constant: 5.75 Lb-In/Amp
> Cont Torque Rating: 34 Lb-In
> Peak Torque: 150 Lb-In
> Weight: 14 lbs
> It is rated for up to 120 Volts, 5.8 amps.
> The motor's back-emf constant is 68.6 Volts/kRPM...so,
> The motor will run 15 RPM for every volt you give it.
> For example, on a 48 volt supply, you could expect 700 RPM for a no-
micro 100 reliance electric
model no e723
serial no g000046
date code 2597
revision b
part no 0723-03-049 A
ccustomer part no 3/4 H.P. PWM
encoder #s heds-5605 A06 0333 A
regards,
keith
Discussion Thread
keith
2003-12-11 09:26:42 UTC
loking for help with power supply for rutex drives...
Dave Fisher
2003-12-11 11:37:39 UTC
Re: [CAD_CAM_EDM_DRO] loking for help with power supply for rutex drives...
ckhaun2000
2003-12-11 17:11:02 UTC
Re: loking for help with power supply for rutex drives...
Dave Fisher
2003-12-11 17:41:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: loking for help with power supply for rutex drives...
Mariss Freimanis
2003-12-11 18:52:42 UTC
Re: loking for help with power supply for rutex drives...
John Johnson
2003-12-11 19:13:25 UTC
Re: [CAD_CAM_EDM_DRO] loking for help with power supply for rutex drives...
Dave Fisher
2003-12-11 20:40:45 UTC
Re: [CAD_CAM_EDM_DRO] loking for help with power supply for rutex drives...
David A. Frantz
2003-12-11 21:02:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: loking for help with power supply for rutex drives...
Jon Elson
2003-12-11 22:29:15 UTC
Re: [CAD_CAM_EDM_DRO] loking for help with power supply for rutex drives...
ckhaun2000
2003-12-11 23:03:31 UTC
Re: loking for help with power supply for rutex drives...