RE: [CAD_CAM_EDM_DRO] Re: New user - Which Engraving CAM software is easiest for beginner?
Posted by
Bill Kichman
on 2004-02-08 20:50:32 UTC
Dear Fred,
I just downloaded a demo of DesnCNC and opened my dxf file as a test...setup
to pocket out the drilled holes and quickly and intuitively generated the
g-code for the entire board's holes (24 total) in one easy fell swoop. It
even interpreted my Autocad text properly. Looks like the ticket so far,
thanks again for the good word!
R. William Kichman, P.E.
Kichman Engineering Associates
103 Old Furnace Road
Cornwall, PA 17016-0643
tel/fax 717/270-0714
-----Original Message-----
From: Fred Smith [mailto:imserv@...]
Sent: Saturday, February 07, 2004 9:31 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: New user - Which Engraving CAM software
is easiest for beginner?
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Bill Kichman"
<billkichman@c...> wrote:
the author. I'm just the guy that spends all day, every day,
teaching people like you, how to use software for CNC machining. Do
you think I would recommend software that was not appropriate for
your stated need? And also do you think that others would sit by
idly if I suggested something about some software program that wasn't
so? I offered you the least expensive solution for your stated need,
it also happens to be the best value in Cam-controller software. (the
only suggestion you received too I notice)
If you wanted to know if DeskCNC would do the job for you, you could
have more appropriately followed up with that question instead of
calling my integrity into question. Even better, download the demo
and ask for help on the DeskCNC user forum.
Fred Smith - IMService
We are THE source for low cost Cad-Cam
http://www.imsrv.com/hobby
February special: DeskCNC + Controller Board + Probe $499
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
I just downloaded a demo of DesnCNC and opened my dxf file as a test...setup
to pocket out the drilled holes and quickly and intuitively generated the
g-code for the entire board's holes (24 total) in one easy fell swoop. It
even interpreted my Autocad text properly. Looks like the ticket so far,
thanks again for the good word!
R. William Kichman, P.E.
Kichman Engineering Associates
103 Old Furnace Road
Cornwall, PA 17016-0643
tel/fax 717/270-0714
-----Original Message-----
From: Fred Smith [mailto:imserv@...]
Sent: Saturday, February 07, 2004 9:31 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: New user - Which Engraving CAM software
is easiest for beginner?
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Bill Kichman"
<billkichman@c...> wrote:
> Thanks Fred, but a recommendation for your software from other thanthe
> author would be more appropriate. I have tested so much "sotouted" "great"
> software lately my fingers are growing tired.You are welcome Bill, I think. However you should know that I'm not
the author. I'm just the guy that spends all day, every day,
teaching people like you, how to use software for CNC machining. Do
you think I would recommend software that was not appropriate for
your stated need? And also do you think that others would sit by
idly if I suggested something about some software program that wasn't
so? I offered you the least expensive solution for your stated need,
it also happens to be the best value in Cam-controller software. (the
only suggestion you received too I notice)
If you wanted to know if DeskCNC would do the job for you, you could
have more appropriately followed up with that question instead of
calling my integrity into question. Even better, download the demo
and ask for help on the DeskCNC user forum.
Fred Smith - IMService
We are THE source for low cost Cad-Cam
http://www.imsrv.com/hobby
February special: DeskCNC + Controller Board + Probe $499
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
Discussion Thread
Bill Kichman
2004-02-05 20:31:59 UTC
New user - Which Engraving CAM software is easiest for beginner?
Fred Smith
2004-02-06 09:18:47 UTC
Re: New user - Which Engraving CAM software is easiest for beginner?
Bill Kichman
2004-02-06 17:10:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: New user - Which Engraving CAM software is easiest for beginner?
stevenson_engineers
2004-02-07 01:13:43 UTC
Re: New user - Which Engraving CAM software is easiest for beginner?
Fred Smith
2004-02-07 08:12:10 UTC
Re: New user - Which Engraving CAM software is easiest for beginner?
Bill Kichman
2004-02-08 20:50:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: New user - Which Engraving CAM software is easiest for beginner?
Kim Lux
2004-02-09 09:39:03 UTC
CNC edgefinding/touch probe update
kdoney_63021
2004-02-09 17:44:59 UTC
Re: CNC edgefinding/touch probe update
Adrian Teo
2004-02-09 21:58:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC edgefinding/touch probe update
Kim Lux
2004-02-10 09:09:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC edgefinding/touch probe update
Kim Lux
2004-02-10 09:09:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC edgefinding/touch probe update
ballendo
2004-02-10 17:02:59 UTC
Re: CNC edgefinding/touch probe update
Roy J. Tellason
2004-02-10 17:58:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC edgefinding/touch probe update
Dave Dillabough
2004-02-11 18:40:28 UTC
Re: [CAD_CAM_EDM_DRO] CNC edgefinding/touch probe update
Kim Lux
2004-02-12 09:04:21 UTC
Re: [CAD_CAM_EDM_DRO] CNC edgefinding/touch probe update