Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Posted by
William Scalione
on 2004-02-20 08:24:38 UTC
I've been running my Z axis servo motor with a Gecko G340 with a Lambda
switcher for a couple of years now. It was going to be just temporary when I
installed it, but since it has worked flawlessly so far, I never got around
to changing it out. I am not using any external capacators on it.
Bill
switcher for a couple of years now. It was going to be just temporary when I
installed it, but since it has worked flawlessly so far, I never got around
to changing it out. I am not using any external capacators on it.
Bill
----- Original Message -----
From: "Ed Gilbert" <co2man@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, February 19, 2004 10:20 PM
Subject: RE: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo
motors for 3 axis router
> Hi Gregory,
>
> What type of machine are you running them on? When you de-accelerate an
axis
> the motor produces voltage back into the power supply, know as back EMF. A
> DC motor whether servo on not is a generator when being turned by the
load.
> A switching supply will not like it when voltage is back induced into its
> output. Makes smoke in most cases! (:/
>
>
> Best,
>
> Ed Gilbert
>
> Gilbert Engineered Systems
> 632 Warrenton-Embro Road
> Macon, NC 27551
> 252-257-0539
> > -----Original Message-----
> > From: Gregory Kamysz [mailto:smsupply@...]
> > Sent: Thursday, February 19, 2004 10:02 PM
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo
> > motors for 3 axis router
> >
> > Is there any reason not to run Gecko 320's on a switching supply? I
> > plan on adding at least 75,000uF of cap between the two. Is cost the
> > main reason for linear supplies? If I set my current limits on the
> > Geckos to never exceed the source current limit all should be well,
> > shouldn't it?
> >
> > Gregory Kamysz
> > Crystal Lake, IL
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> > timg@...
> > Moderator: pentam@... indigo_red@... davemucha@...
> > [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> > if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> > sister site to the CCED group, as many of the same members are there,
for
> > OT subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
>
>
> -------------------------------------
> This message has been scanned for viruses and
> dangerous content by NCOL.NET, and is believed to be clean.
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
Discussion Thread
plastiguy
2004-02-19 13:30:23 UTC
Power Supply for Gecko 320 and servo motors for 3 axis router
Roy J. Tellason
2004-02-19 13:52:27 UTC
Re: [CAD_CAM_EDM_DRO] Power Supply for Gecko 320 and servo motors for 3 axis router
caudlet
2004-02-19 15:25:00 UTC
Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Gregory Kamysz
2004-02-19 18:58:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
bull2003winkle
2004-02-19 20:57:08 UTC
Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Jon Elson
2004-02-19 21:36:18 UTC
Re: [CAD_CAM_EDM_DRO] Power Supply for Gecko 320 and servo motors for 3 axis router
Jon Elson
2004-02-19 21:46:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Ed Gilbert
2004-02-19 23:38:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
William Scalione
2004-02-20 08:24:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Jon Elson
2004-02-20 09:05:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Jon Elson
2004-02-20 09:50:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
caudlet
2004-02-20 13:48:30 UTC
Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Kim Lux
2004-02-20 18:51:04 UTC
CNC Probing secrets...
Jon Elson
2004-02-20 19:38:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Roy J. Tellason
2004-02-20 20:42:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router
Gregory Kamysz
2004-02-21 07:04:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power Supply for Gecko 320 and servo motors for 3 axis router