CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: servomotor suitability???

Posted by sdfine@d...
on 2004-03-15 16:46:34 UTC
What is the C&H web site address?

-----Original Message-----
From: caudlet [mailto:info@...]
Sent: Monday, March 15, 2004 5:26 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: servomotor suitability???


--- In CAD_CAM_EDM_DRO@yahoogroups.com, Erie Patsellis <erie@s...>
wrote:
> has anyone looked at *C&H surpus #DCME9850???*
>
> **
>
> I'm building a router table for a friend and am trying to find
suitable
> servo motors. drive is going to be timing belt, approx 6 to 1
reduction.
> gantry weight is estimated at about 200 pounds.
>
>
> erie
>
> **

Erie I just got a C&H catalog in yesterday. I will take a look and
also check their web site. They usually have some pretty good DC
motors that could be enticed to operate as servos. Some of the DC
motors have mounting holes and a rear shaft to be able to add
encoders. If you can find that you are pretty much there. I will
report back later. Seems to be lots of AC or brushless DC servos on
EBAY right now. The group over at OSMC have come up with some roll- ur-own
BLDC motor controllers. Is the gantry going to be greater
than 3 ft across? Are you considering dual drives (separate motor
and motor drivers) on the gantry?



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill List
Mom List Owner


Yahoo! Groups Links

Discussion Thread

Erie Patsellis 2004-03-15 13:19:17 UTC servomotor suitability??? caudlet 2004-03-15 14:26:42 UTC Re: servomotor suitability??? sdfine@d... 2004-03-15 16:46:34 UTC RE: [CAD_CAM_EDM_DRO] Re: servomotor suitability??? Kim Lux 2004-03-15 16:47:16 UTC Request for assistance with Gecko and LARGE servo motor... caudlet 2004-03-15 20:07:23 UTC Re: servomotor suitability??? Jon Elson 2004-03-15 20:20:20 UTC Re: [CAD_CAM_EDM_DRO] Re: servomotor suitability??? Jon Elson 2004-03-15 20:26:11 UTC Re: [CAD_CAM_EDM_DRO] Re: servomotor suitability??? Jon Elson 2004-03-15 20:41:18 UTC Re: [CAD_CAM_EDM_DRO] Request for assistance with Gecko and LARGE servo motor... Erie Patsellis 2004-03-16 06:03:36 UTC Re: [CAD_CAM_EDM_DRO] Re: servomotor suitability??? caudlet 2004-03-16 12:05:39 UTC Re: servomotor suitability???