CAD CAM EDM DRO - Yahoo Group Archive

Re: camtronics driver

Posted by Dan Mauch
on 1999-06-11 06:27:30 UTC
When I first started selling complete controllers with case fans and power
supplies installed, I found that the case was the show stoppper. Like you
said most of them were in the $120 range and using a PC case did not lend
themselves for a nice looking product. Then I found Sescom. You can get a
catalog from them by calling 800-634-3457 I use their MC series cabinets.
What is really nice about them is that it is all flat panels that can be
easily machined and then you assemble it with extruded rails to lock it
together. Then I decided to have the back panels silk screened for the
connectors. Last, I do all the machining of the cases. The price for the
bare case is ~$44.

Dan
-----Original Message-----
From: Tim Goldstein <timg@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Thursday, June 10, 1999 9:41 PM
Subject: Re: [CAD_CAM_EDM_DRO] camtronics driver


>From: "Tim Goldstein" <timg@...>
>
>Dan,
>
>Is the case you are using an off the shelf unit or do you make it? I hunted
>all over and the only enclosure I could find that was at least that big was
>designed to mount in a 19" rack unit and cost around $120. I ended up
making
>my own case out of masonite with a particle board base.
>
>
>Tim
>[Denver, CO]
>
>
>> -----Original Message-----
>> From: Dan Mauch [mailto:dmauch@...]
>> Sent: Thursday, June 10, 1999 6:46 AM
>> To: CAD_CAM_EDM_DRO@onelist.com
>> Subject: Re: [CAD_CAM_EDM_DRO] camtronics driver
>>
>>
>> From: "Dan Mauch" <dmauch@...>
>>
>> On my 5 amp controller I place everything in a 12X10X6 case . The fan was
>> mounted on the outside of the case and the transformers are located
inside
>> the case. The transformers are on one side of the case and the drivers
are
>> on the other. No problems with noise.
>> Dan
>> -----Original Message-----
>> From: Al Schoepp <aschoepp@...>
>> To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
>> Date: Wednesday, June 09, 1999 6:11 PM
>> Subject: [CAD_CAM_EDM_DRO] camtronics driver
>>
>>
>> >From: Al Schoepp <aschoepp@...>
>> >
>> >Just curious, I'm in the process of constructing on of Dan's 5A stepper
>> >drivers and was wondering if it's ok to put the transformer/power supply
>> >components in the same enclosure. I'm new to all of this stuff and was
>> >wondering if the AC current in the enclosure would end up creating a lot
>> >of noise that would affect the stepper driver operation.
>> >
>> >Thanks,
>> >Al
>> >
>> >------------------------------------------------------------------------
>> >Campaign 2000 is here!
>> >http://www.onelist.com
>> >Discuss your thoughts; get informed at ONElist. See our homepage.
>> >------------------------------------------------------------------------
>> >welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for the
>> discussion of shop built systems in the above catagories.
>> >
>>
>>
>> ------------------------------------------------------------------------
>> What do lizards and rock music have in common?
>> http://www.onelist.com
>> They both have communities at ONElist. Find yours today!
>> ------------------------------------------------------------------------
>> welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for
>> the discussion of shop built systems in the above catagories.
>>
>
>
>------------------------------------------------------------------------
>With more than 20 million e-mails exchanged daily...
>http://www.onelist.com
>...ONElist is home to the liveliest discussions on the Internet!
>------------------------------------------------------------------------
>welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe:
> http://www.onelist.com/unsubscribe/CAD_CAM_EDM_DRO
>bill, List Manager
>

Discussion Thread

Al Schoepp 1999-06-09 16:22:47 UTC camtronics driver Mo 1999-06-09 18:39:41 UTC Re: camtronics driver Mo 1999-06-09 18:51:44 UTC Re: camtronics driver Dan Mauch 1999-06-10 05:45:59 UTC Re: camtronics driver Tim Goldstein 1999-06-10 20:20:07 UTC Re: camtronics driver Al Schoepp 1999-06-10 22:56:21 UTC Re: camtronics driver Dan Mauch 1999-06-11 06:27:30 UTC Re: camtronics driver Tim Goldstein 1999-06-11 08:47:23 UTC Re: camtronics driver Dan Mauch 1999-06-12 06:15:17 UTC Re: camtronics driver