CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] cnc plasma gizmo

Posted by AbbyKatt
on 2004-06-29 13:48:56 UTC
Maybe what the solution is then, is to simply make it 4-axis, and have a
small stepper/servo control for tilting it. Then you'd just setup your
G-code output from your program that generates the output files to put
the tilt in beforehand. i.e> tilt 45 degrees, move X amount at certain
slow feed rate, then tilt to 90.

And then you could bevel what you wanted at will, too. :)




-----Original Message-----
From: Jens Swales [mailto:jipeess2000@...]
Sent: 29 June 2004 20:21
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] cnc plasma gizmo


hi all

im just about to build a prototype from scratch and still have some
time (and money) left to optimize a little here and there. as i
understand, piercing seems to be what kills the tips in the long run.
wouldnt it be neat to have the torch attached to some sort of device,
pneumatic, electromagnetic or whatever, that tilts the torch a few
degs, just enough to avoid the splattering getting straight into the
tip and then let the arc-good signal, activate the tilting thing to
straighten up the torch for the proceeding cut...

ive seen some cnc flame torches mounted on a similar device for
making bevel cuts though, so this is maybee just like re-inventing
the wheel.

js



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill
List Mom List Owner


Yahoo! Groups Links

Discussion Thread

Jens Swales 2004-06-29 12:22:04 UTC cnc plasma gizmo AbbyKatt 2004-06-29 13:48:56 UTC RE: [CAD_CAM_EDM_DRO] cnc plasma gizmo Hal Eckhart 2004-06-29 17:03:50 UTC Re: [CAD_CAM_EDM_DRO] cnc plasma gizmo Raymond Heckert 2004-06-29 19:17:26 UTC Re: [CAD_CAM_EDM_DRO] cnc plasma gizmo Jeffrey Martin 2004-06-29 21:30:53 UTC Re: [CAD_CAM_EDM_DRO] cnc plasma gizmo caudlet 2004-06-30 11:37:06 UTC Re: cnc plasma gizmo