Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Posted by
Dennis Cartier
on 2004-08-03 17:26:52 UTC
Jon Elson wrote:
asked the seller beforehand to make sure it had ballscrews and servos.
He confirmed that it didn't use scales, but was unsure as to what it did
use. I guess at the worst I will have to come up with a way to add
encoders into the control loop. Perhaps driven off the ballscrews?
go for? That would still be required with a 480V VFD right?
Thanks for the help,
Dennis
>It must have some form of feedback ... but I am sure it is not scales. I
> Yup, thse are servos for sure. I didn't see any encoders/resolvers/scales
> anywhere in the pictures.
>
>
asked the seller beforehand to make sure it had ballscrews and servos.
He confirmed that it didn't use scales, but was unsure as to what it did
use. I guess at the worst I will have to come up with a way to add
encoders into the control loop. Perhaps driven off the ballscrews?
>I guess the million dollar question is what do 240 to 480 transformers
> No, that's why VFD's are so great! They do the phase conversion, too.
> If you intend to run the motor at full power for extended times, you
> might want
> to use a slightly higher rated VFD so the rectifier/cap bank won't be
> overstressed
> from the single phase power, but they run just fine with single phase input.
> Surplus VFDs are constantly on eBay, and if you can wait a month or two,
> a good deal will certainly come along. Actually, 480 V VFDs in modest sizes
> often go much cheaper than 240 V units, as everyone wanting to use them
> in their garage want the 240 V VFD's.
>
go for? That would still be required with a 480V VFD right?
Thanks for the help,
Dennis
Discussion Thread
Dennis Cartier
2004-08-02 09:47:42 UTC
Anyone Familiar with an MHP S-24 CNC
Bob Muse
2004-08-02 14:25:22 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Jon Elson
2004-08-02 17:36:25 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Dennis Cartier
2004-08-02 19:56:45 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Jon Elson
2004-08-02 22:30:44 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
m37grady
2004-08-03 14:14:28 UTC
Re: Anyone Familiar with an MHP S-24 CNC
Dennis Cartier
2004-08-03 16:15:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Anyone Familiar with an MHP S-24 CNC
Dennis Cartier
2004-08-03 17:26:52 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Jon Elson
2004-08-03 20:22:22 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Dennis Cartier
2004-08-05 02:51:32 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC
Jon Elson
2004-08-05 09:07:13 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Familiar with an MHP S-24 CNC