Re: [CAD_CAM_EDM_DRO] the mc3479p ic?

Check out http://www.seanet.com/~dmauch/ if you haven't already.
They have some 5 amp motor translator PCBs.
They don't use the mc3479p though.
James

----- Original Message -----
From: Derek Barger <hightechsystems@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Wednesday, May 03, 2000 8:34 AM
Subject: Re: [CAD_CAM_EDM_DRO] the mc3479p ic?


> James:
> I do have the data sheets the 350ma is direct drive from the chip itself
> to the motor. Transistors can change this to a 5A drive. All the other
> chip makers that say they drive 5A, don't directly you have to add
> transistors.
>
> Derek
>
> James Cullins wrote:
> >
> > Use www.Findchips.com to get the data sheets on it. I believe this chip
is
> > only good for
> > about 350ma per coil.
> > Jim
> > ----- Original Message -----
> > From: Derek Barger <hightechsystems@...>
> > To: <CAD_CAM_EDM_DRO@egroups.com>
> > Sent: Tuesday, May 02, 2000 9:29 PM
> > Subject: [CAD_CAM_EDM_DRO] the mc3479p ic?
> >
> > Hi fellow listers,
> >
> > Question has anyone used this ic in a bipolar stepper drive to drive 5A
> > loads?
> > Any pc-board examples out there?
> > Anyone used this with EMC?
> >
> > Derek
> >
> > ------------------------------------------------------------------------
> > Get paid for the stuff you know!
> > Get answers for the stuff you don't. And get $10 to spend on the site!
> > http://click.egroups.com/1/2200/2/_/423600/_/957321273/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> > discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
> >
> > ------------------------------------------------------------------------
> > SHOPPING for DEALS? The merchants at BuyItOnline.com are offering up
> > to 30% OFF great gear, wear, gadgets and more, now through April 15,
> > 2000. Real stores. Real Deals. Real Easy. Go get something great!
> > http://click.egroups.com/1/3025/2/_/423600/_/957358926/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> ------------------------------------------------------------------------
> Avoid the lines and visit avis.com for quick and easy online
> reservations. Enjoy a compact car nationwide for only $29 a day!
> Click here for more details.
> http://click.egroups.com/1/3011/2/_/423600/_/957361184/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>