Re: [CAD_CAM_EDM_DRO] Analog Output controller?
Posted by
Brad Eyben
on 2004-09-11 07:08:09 UTC
Just a small correction Jon,
These are Brushed motor drives and won't drive brushless.
Also they won't accept encoder inputs...just tachs or hall sensors.
Cheers,
Brad
These are Brushed motor drives and won't drive brushless.
Also they won't accept encoder inputs...just tachs or hall sensors.
Cheers,
Brad
----- Original Message -----
From: "Jon Elson" <elson@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, September 11, 2004 12:12 AM
Subject: Re: [CAD_CAM_EDM_DRO] Analog Output controller?
> jracingrc wrote:
>
> >Hi guys,
> >
> >I have 3 of these AMC Servo Amplifiers B30A8:
> >http://www.a-m-c.com/products/trap.htm
> >
> >I was wondering, how do I get these to control the motor? I think
> >they need an analog output controller to send a +/- 10V command
> >signal, but I'm really in the dark about these things. I've
> >seen "motion controllers" on ebay, but I'm not sure how I go about
> >connecting those things to the AMC amplifiers I have. Are there any
> >relatively inexpensive controllers that I can use with these
> >amplifiers??
> >
> >
> OK, these are analog servo amplifiers for brushless motors (but they can
> drive brush motors, too.) Do you have the motors?
>
> >Ideally I'd like to have closed loop, where the computer knows the
> >position of the motors, but open loop like the stepper systems is
> >fine too.
> >
> >
> >
> Well, I have a product that will do it. It is called the PPMC, and my web
> page is http://jelinux.pico-systems.com/PPMC.html
>
> It has an encoder counter board, a DAC board to produce the velocity
> command signals to the servo amp, and a digital I/O board for limit
> switches and spindle and coolant control.
>
> This hardware is supported by EMC, which does accept position information
> from the encoders on the motors.
> See http://www.linuxcnc.org/ for more info on EMC.
>
> Jon
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members
are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
Discussion Thread
jracingrc
2004-09-10 21:42:08 UTC
Analog Output controller?
vavaroutsos
2004-09-10 22:39:19 UTC
Re: Analog Output controller?
Jon Elson
2004-09-10 23:16:52 UTC
Re: [CAD_CAM_EDM_DRO] Analog Output controller?
Brad Eyben
2004-09-11 07:08:09 UTC
Re: [CAD_CAM_EDM_DRO] Analog Output controller?
Peter Renolds
2004-09-11 07:59:07 UTC
Re: [CAD_CAM_EDM_DRO] Analog Output controller?
vrsculptor
2004-09-11 08:42:44 UTC
Re: Analog Output controller?
Jon Elson
2004-09-11 09:33:12 UTC
Re: [CAD_CAM_EDM_DRO] Analog Output controller?
Jon Elson
2004-09-11 09:36:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?
R Rogers
2004-09-11 12:03:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?
Jon Elson
2004-09-11 15:03:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?
erie
2004-09-11 15:11:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?
Brad Eyben
2004-09-12 02:58:48 UTC
Re: [CAD_CAM_EDM_DRO] Analog Output controller?
stepperman
2004-09-12 19:38:40 UTC
Re: Analog Output controller?
Jon Elson
2004-09-12 22:08:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?
Paul
2004-09-13 01:08:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Analog Output controller?