CAD CAM EDM DRO - Yahoo Group Archive

Re: Two Lamps?

Posted by Torsten
on 2004-12-14 10:41:12 UTC
> > -----Original Message-----
> > From: Torsten [mailto:torsten@g...]
> > Sent: 25 October 2004 18:17
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: [CAD_CAM_EDM_DRO] Two Lamps?
> >
> >
> >
> >
> > Got a question, I have a Powersupply
> > delivering 55 volts DC in my driverbox
> > connected to a Caps to store and smuth
> > out the current having been zapped a few
> > times I would like to hook up a little
> > light bulb to drain out the current after
> > it is shut off.
> > Would also be nice for the visual feedback
> > to see when the thing is charged.
> >
> > On the first attempt I learned that a Led dose
> > not work with DC current.
> >
> > So now I am Looking at some Bulbs with a filament.
> > What I found is a "Miniature Bayonet base Lamp"
> > rated for 28 volt .040 amps I belive I should be
> > able to wire two of them in serial to make it work
> > on my 55 volt system.
> >
> > Will this work?
> > Any thoughts, please share.
> >
> >

Finally got the bulbs this week and tryed them out.
It worked sort of, the Light drained the power after
about one minute or so just what I wanted.
Strange thing is only one of the bulbs lighted up the
other one did not seam to be on.
Because they where wired in series I know electricity
must have gone through both of them.
What is going on, anybody know why only one light was on?
How do I fix it.

Discussion Thread

Torsten 2004-10-25 10:16:49 UTC Two Lamps? Dave Fisher 2004-10-25 10:36:34 UTC RE: [CAD_CAM_EDM_DRO] Two Lamps? Bengt 2004-10-25 10:44:48 UTC Re: Two Lamps? Andy Wander 2004-10-25 10:49:27 UTC RE: [CAD_CAM_EDM_DRO] Two Lamps? Torsten 2004-10-25 11:13:08 UTC Re: Two Lamps? Roy J. Tellason 2004-10-25 11:22:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Steven Ciciora 2004-10-25 15:35:26 UTC RE: [CAD_CAM_EDM_DRO] Two Lamps? Torsten 2004-12-14 10:41:12 UTC Re: Two Lamps? R Rogers 2004-12-14 11:15:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Dave Fisher 2004-12-14 11:21:02 UTC RE: [CAD_CAM_EDM_DRO] Re: Two Lamps? Randy Wilson 2004-12-14 14:58:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Tom Hubin 2004-12-14 18:32:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Hugh Prescott 2004-12-14 19:29:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Torsten 2004-12-14 20:44:31 UTC Re: Two Lamps? JanRwl@A... 2004-12-14 21:18:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Randy Wilson 2004-12-14 21:39:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps? Torsten 2004-12-15 18:55:14 UTC Re: Two Lamps? Randy Wilson 2004-12-15 19:20:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?