Re: Two Lamps?
Posted by
Torsten
on 2004-12-15 18:55:14 UTC
I went out and got the proper resistor you
recommended and it works great with only
one bulb now.
Thanks for been patient with me, I learned something.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Randy Wilson <yahooey@r...>
wrote:
recommended and it works great with only
one bulb now.
Thanks for been patient with me, I learned something.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Randy Wilson <yahooey@r...>
wrote:
>infrared
> On Dec 14, 2004, at 11:43 PM, Torsten wrote:
> >
> > Some body suggested using only one bulb and a
> > resistor.
>
> That would be me.
>
> > The only Resistor I have laying here is a
> > 4.7 k-Ohm 1/2 watt type.
>
> This is almost five times more resistance than what I suggested for
> your MAXIMUM resistance value.
>
> > I tryed wiring this in series with one bulp
> > but I got nothing no light at all.
> > Should there not be at least something.
>
> Of course not. If there is not enough current flowing to heat the
> filament adequately, so unless your vision extends into the
> you won't see squat. The value you used will permit 5ma to flow asis
> opposed to the 27ma starting point I suggested or the 40ma the bulb
> rated for.
>
Discussion Thread
Torsten
2004-10-25 10:16:49 UTC
Two Lamps?
Dave Fisher
2004-10-25 10:36:34 UTC
RE: [CAD_CAM_EDM_DRO] Two Lamps?
Bengt
2004-10-25 10:44:48 UTC
Re: Two Lamps?
Andy Wander
2004-10-25 10:49:27 UTC
RE: [CAD_CAM_EDM_DRO] Two Lamps?
Torsten
2004-10-25 11:13:08 UTC
Re: Two Lamps?
Roy J. Tellason
2004-10-25 11:22:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Steven Ciciora
2004-10-25 15:35:26 UTC
RE: [CAD_CAM_EDM_DRO] Two Lamps?
Torsten
2004-12-14 10:41:12 UTC
Re: Two Lamps?
R Rogers
2004-12-14 11:15:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Dave Fisher
2004-12-14 11:21:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Randy Wilson
2004-12-14 14:58:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Tom Hubin
2004-12-14 18:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Hugh Prescott
2004-12-14 19:29:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Torsten
2004-12-14 20:44:31 UTC
Re: Two Lamps?
JanRwl@A...
2004-12-14 21:18:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Randy Wilson
2004-12-14 21:39:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?
Torsten
2004-12-15 18:55:14 UTC
Re: Two Lamps?
Randy Wilson
2004-12-15 19:20:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Two Lamps?