Re: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Posted by
Steve Carlisle
on 2000-06-01 16:55:37 UTC
Dan Mauch at one time said he fooled with the PIC-SERVO's
and was dissapointed with the top speeds available. Hope
he will give us more info on that project.
Steve
----------
From: Carlos Guillermo <carlos@...>
To: CAD_CAM_EDM_DRO@egroups.com
Subject: RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Date: Thursday, June 01, 2000 4:53 PM
Andrew -
I've thought about using the JRKerr setup. How's the smoothness and
following error with the step/dir input version? Also, what kind of speeds
can you get, and what's the limiting factor?
Thanks in advance,
Carlos Guillermo
VERVE Engineering & Design
@Backup- Protect and Access your data any time, any where on the net.
Try @Backup FREE and recieve 300 points from mypoints.com Install now:
http://click.egroups.com/1/4873/3/_/423600/_/959903329/
------------------------------------------------------------------------
Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager
and was dissapointed with the top speeds available. Hope
he will give us more info on that project.
Steve
----------
From: Carlos Guillermo <carlos@...>
To: CAD_CAM_EDM_DRO@egroups.com
Subject: RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Date: Thursday, June 01, 2000 4:53 PM
Andrew -
I've thought about using the JRKerr setup. How's the smoothness and
following error with the step/dir input version? Also, what kind of speeds
can you get, and what's the limiting factor?
Thanks in advance,
Carlos Guillermo
VERVE Engineering & Design
> -----Original Message-----------------------------------------------------------------------------
> From: andrew abken [mailto:kn6za@...]
> Sent: Thursday, June 01, 2000 9:34 AM
> To: CAD_CAM_EDM_DRO@egroups.com
> Subject: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
>
>
>
>
>
> I have set up a three axis minimill with the jr-kerr stuff and
> drive them
> with the step/dir output on emc. Just looking for others who have worked
> with them and who wish to make a comment on their experience.
>
> My system went together well, and works nicely for my small machine. I
> don't think I would use them on anything larger than a minimill.
>
> Have you seen the machine controller program up on their web site? It
> works, but without backlash compensation its a bit useless. If I ever get
> more time I would like to work on that program and make it more usable,
> being that its open source.
>
>
> thanks,
> andrew
@Backup- Protect and Access your data any time, any where on the net.
Try @Backup FREE and recieve 300 points from mypoints.com Install now:
http://click.egroups.com/1/4873/3/_/423600/_/959903329/
------------------------------------------------------------------------
Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager
Discussion Thread
andrew abken
2000-06-01 06:33:44 UTC
anyone using jr-kerr servos
Carlos Guillermo
2000-06-01 16:48:55 UTC
RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Steve Carlisle
2000-06-01 16:55:37 UTC
Re: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Andy Olney
2000-06-01 22:24:32 UTC
RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Andy Olney
2000-06-01 22:25:09 UTC
RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Dan Mauch
2000-06-02 07:36:49 UTC
Re: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
Ron Ginger
2000-06-02 08:16:50 UTC
Re: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
andy@o...
2000-06-02 13:07:15 UTC
Re: anyone using jr-kerr servos
andrew abken
2000-06-02 18:46:18 UTC
RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos
andrew abken
2000-06-02 19:36:27 UTC
RE: [CAD_CAM_EDM_DRO] anyone using jr-kerr servos