RE: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force unit

Hi Clint,

That is just great
thanks

Roger

-----Original Message-----
From: topdown210 [mailto:topdown210@...]
Sent: 05 March 2005 21:50
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force unit




Hi,

I have one of those sitting in front of me... The pin out is from left
to right looking from the 8 pin input end. The first two pins are for
the opto supply in and out. Pin 1 is in and pin 2 is out. Opto out
supplies 5V regulated. I jumper these for my steppers. Pin 3 is logic
common. That's where I connect the common for my step/ direction
inputs. Pin 4 is current reduction. If you don't need less than 2 amps
connect nothing. A resistor between pin 4 and logic common will reduce
the current to the motor. I don't connect anything to this for my
motors. pin 5 is AWO (all windings off). I don't use this pin for my
motors. Pin 6 is half step/ full step. Connect nothing for half
step... connect to logic common for full step. Pin 7 is direction.
logic high or low. Pin 8 is pulse or clock or step... different words
for the same thing. The step pulses on the negative going signal and
50 microseconds are recommended.

The power supply needs a 1000 uf capacitor between 0V and 30V.

I hope this helps you.

Clint

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
<r_.hampson@t...> wrote:

> Hi Wally
>
> I only have one module
>
> A scanner will give a large file when scanning colour if set to

black /

> white file size should be only a few hundred Kb, you could also zip

the

> files to make them even smaller
>
> But if this is too dificult
>
> Do you have a digital camera, or know somebody who has then you

could take a

> photograph of the pages on close macro
>
> or describe the inputs to me.
>
> Thanks
>
>
> Roger


>
> -----Original Message-----
> From: cnc_4_me [mailto:cnc4me@g...]
> Sent: 05 March 2005 20:52
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force unit
>
>
>
>
> i can try to set up scanner..never used it...i expect large file,

how

> can i send to you..most email limited to 1 or 2 meg.
>
>
> Wally
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
> <r_.hampson@t...> wrote:
> > Hi Wally
> >
> > There is a sticker on it showing the output connections but no
> information
> > on input
> >
> > I would like this and any wiring info to controller
> >
> > Any chance of a PDF copy
> >
> > Roger
> >
> >
> > -----Original Message-----
> > From: cnc_4_me [mailto:cnc4me@g...]
> > Sent: 05 March 2005 17:48
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force unit
> >
> >
> >
> >
> > I have the full manual for it...Like 9 pages without the
> > curves...What do you want to know...the drive should have a

sticker

> > on it with hook up info. How many of these do you have..
> >
> >
> > Wally
> >
> >
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
> > <r_.hampson@t...> wrote:
> > > Hi guys.
> > >
> > > I have just picked up a slo-syn 230t 2A 30V translator module.
> > >
> > > Would anyone have a datasheet on this module so that I can
> > configure it??
> > >
> > > I was thinking whether it could be used on my rotary table
> > >
> > > Roger UK
> > >
> > > -----Original Message-----
> > > From: Imran Jawaid [mailto:av1a@y...]
> > > Sent: 05 March 2005 10:53
> > > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > > Subject: [CAD_CAM_EDM_DRO] Re: Torque from Force unit
> > >
> > >
> > >
> > >
> > > Isn't that Kgf unit for Force?
> > > like you can convert 3.8x9.8 = 37.2Newtons
> > >
> > > Kgf-m or Kgf-cm is a unit of torque
> > >
> > > Since Torque = distance x force
> > > Then need to calculate Torque= distance x 37.2
> > >
> > > I can be wrong as 3.8x18.877 = 71.7 (as mentioned by Dan) which
> is i
> > > think pretty decend torque for small medium Milling.
> > >
> > >
> > >
> > > Imran
> > >
> > > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dan Mauch"

<dmauch@s...>

> > > wrote:
> > > > kg.cm.s to oz in multiply by 18.877 to get oz in
> > > > Dan
> > > > ----- Original Message -----
> > > > From: "Imran Jawaid" <av1a@y...>
> > > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > > Sent: Friday, March 04, 2005 10:24 AM
> > > > Subject: [CAD_CAM_EDM_DRO] Torque from Force unit
> > > >
> > > >
> > > > >
> > > > >
> > > > > I've an AC servo which i'm replacing with DC Servo
> > > > >
> > > > > the specs of AC motor says
> > > > > WT = 3.8Kgf (which is obviously force not Torque as it is

not

> > Kgf-
> > > m or
> > > > > Kgf-cm)
> > > > > Power is 300 Watts
> > > > > How can i find the torque then ?
> > > > >
> > > > > Well it look really easy but in the end...
> > > > >
> > > > > Regards,
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Addresses:
> > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > >
> > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > > wanliker@a...,
> > > > > timg@k...
> > > > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > > > [Moderators]
> > > > > URL to this group:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > >
> > > > > OFF Topic POSTS: General Machining
> > > > > If you wish to post on unlimited OT subjects goto:
> > > > > aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to
> > > reach it
> > > > > if you have trouble.
> > > > > http://www.metalworking.com/news_servers.html
> > > > >
> > > > > http://groups.yahoo.com/group/jobshophomeshop I consider
> this
> > > to be a
> > > > > sister site to the CCED group, as many of the same members

are

> > > there, for
> > > > > OT subjects, that are not allowed on the CCED list.
> > > > >
> > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > > POSTING THEM.
> > > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> > > > > bill
> > > > > List Mom
> > > > > List Owner
> > > > >
> > > > >
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > >
> > >
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a...,
> > > timg@k...
> > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this

to

> > be a
> > > sister site to the CCED group, as many of the same members are
> > there, for OT
> > > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY

POSTING

> > THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > > Yahoo! Groups Links
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,

wanliker@a...,

> > timg@k...
> > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to
> be a
> > sister site to the CCED group, as many of the same members are
> there, for OT
> > subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...,
> timg@k...
> Moderator: pentam@c... indigo_red@q... davemucha@j...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to

reach it if

> you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to

be a

> sister site to the CCED group, as many of the same members are

there, for OT

> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING

THEM.

> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links