slo-syn 230t Re: Torque from Force unit

Clint, do you want me to email you the manual to.


Wally


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "topdown210"
<topdown210@y...> wrote:

>
> Hi,
>
> I have one of those sitting in front of me... The pin out is from

left

> to right looking from the 8 pin input end. The first two pins are

for

> the opto supply in and out. Pin 1 is in and pin 2 is out. Opto out
> supplies 5V regulated. I jumper these for my steppers. Pin 3 is

logic

> common. That's where I connect the common for my step/ direction
> inputs. Pin 4 is current reduction. If you don't need less than 2

amps

> connect nothing. A resistor between pin 4 and logic common will

reduce

> the current to the motor. I don't connect anything to this for my
> motors. pin 5 is AWO (all windings off). I don't use this pin for my
> motors. Pin 6 is half step/ full step. Connect nothing for half
> step... connect to logic common for full step. Pin 7 is direction.
> logic high or low. Pin 8 is pulse or clock or step... different

words

> for the same thing. The step pulses on the negative going signal and
> 50 microseconds are recommended.
>
> The power supply needs a 1000 uf capacitor between 0V and 30V.
>
> I hope this helps you.
>
> Clint
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
> <r_.hampson@t...> wrote:
> > Hi Wally
> >
> > I only have one module
> >
> > A scanner will give a large file when scanning colour if set to
> black /
> > white file size should be only a few hundred Kb, you could also

zip

> the
> > files to make them even smaller
> >
> > But if this is too dificult
> >
> > Do you have a digital camera, or know somebody who has then you
> could take a
> > photograph of the pages on close macro
> >
> > or describe the inputs to me.
> >
> > Thanks
> >
> >
> > Roger
>
>
> >
> > -----Original Message-----
> > From: cnc_4_me [mailto:cnc4me@g...]
> > Sent: 05 March 2005 20:52
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force unit
> >
> >
> >
> >
> > i can try to set up scanner..never used it...i expect large file,
> how
> > can i send to you..most email limited to 1 or 2 meg.
> >
> >
> > Wally
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
> > <r_.hampson@t...> wrote:
> > > Hi Wally
> > >
> > > There is a sticker on it showing the output connections but no
> > information
> > > on input
> > >
> > > I would like this and any wiring info to controller
> > >
> > > Any chance of a PDF copy
> > >
> > > Roger
> > >
> > >
> > > -----Original Message-----
> > > From: cnc_4_me [mailto:cnc4me@g...]
> > > Sent: 05 March 2005 17:48
> > > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > > Subject: [CAD_CAM_EDM_DRO] slo-syn 230t Re: Torque from Force

unit

> > >
> > >
> > >
> > >
> > > I have the full manual for it...Like 9 pages without the
> > > curves...What do you want to know...the drive should have a
> sticker
> > > on it with hook up info. How many of these do you have..
> > >
> > >
> > > Wally
> > >
> > >
> > >
> > > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roger Hampson"
> > > <r_.hampson@t...> wrote:
> > > > Hi guys.
> > > >
> > > > I have just picked up a slo-syn 230t 2A 30V translator

module.

> > > >
> > > > Would anyone have a datasheet on this module so that I can
> > > configure it??
> > > >
> > > > I was thinking whether it could be used on my rotary table
> > > >
> > > > Roger UK
> > > >
> > > > -----Original Message-----
> > > > From: Imran Jawaid [mailto:av1a@y...]
> > > > Sent: 05 March 2005 10:53
> > > > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > Subject: [CAD_CAM_EDM_DRO] Re: Torque from Force unit
> > > >
> > > >
> > > >
> > > >
> > > > Isn't that Kgf unit for Force?
> > > > like you can convert 3.8x9.8 = 37.2Newtons
> > > >
> > > > Kgf-m or Kgf-cm is a unit of torque
> > > >
> > > > Since Torque = distance x force
> > > > Then need to calculate Torque= distance x 37.2
> > > >
> > > > I can be wrong as 3.8x18.877 = 71.7 (as mentioned by Dan)

which

> > is i
> > > > think pretty decend torque for small medium Milling.
> > > >
> > > >
> > > >
> > > > Imran
> > > >
> > > > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dan Mauch"
> <dmauch@s...>
> > > > wrote:
> > > > > kg.cm.s to oz in multiply by 18.877 to get oz in
> > > > > Dan
> > > > > ----- Original Message -----
> > > > > From: "Imran Jawaid" <av1a@y...>
> > > > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > > > Sent: Friday, March 04, 2005 10:24 AM
> > > > > Subject: [CAD_CAM_EDM_DRO] Torque from Force unit
> > > > >
> > > > >
> > > > > >
> > > > > >
> > > > > > I've an AC servo which i'm replacing with DC Servo
> > > > > >
> > > > > > the specs of AC motor says
> > > > > > WT = 3.8Kgf (which is obviously force not Torque as it is
> not
> > > Kgf-
> > > > m or
> > > > > > Kgf-cm)
> > > > > > Power is 300 Watts
> > > > > > How can i find the torque then ?
> > > > > >
> > > > > > Well it look really easy but in the end...
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > Addresses:
> > > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > > FILES:

http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

> > > > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > > >
> > > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > > > wanliker@a...,
> > > > > > timg@k...
> > > > > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > > > > [Moderators]
> > > > > > URL to this group:
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > > >
> > > > > > OFF Topic POSTS: General Machining
> > > > > > If you wish to post on unlimited OT subjects goto:
> > > > > > aol://5863:126/rec.crafts.metalworking or go thru

Google.com

> > to
> > > > reach it
> > > > > > if you have trouble.
> > > > > > http://www.metalworking.com/news_servers.html
> > > > > >
> > > > > > http://groups.yahoo.com/group/jobshophomeshop I consider
> > this
> > > > to be a
> > > > > > sister site to the CCED group, as many of the same members
> are
> > > > there, for
> > > > > > OT subjects, that are not allowed on the CCED list.
> > > > > >
> > > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > > > POSTING THEM.
> > > > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > EXCEPTIONS........
> > > > > > bill
> > > > > > List Mom
> > > > > > List Owner
> > > > > >
> > > > > >
> > > > > > Yahoo! Groups Links
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > >
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > wanliker@a...,
> > > > timg@k...
> > > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > > [Moderators]
> > > > URL to this group:

http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > > aol://5863:126/rec.crafts.metalworking or go thru Google.com

to

> > > reach it if
> > > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider

this

> to
> > > be a
> > > > sister site to the CCED group, as many of the same members are
> > > there, for OT
> > > > subjects, that are not allowed on the CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING
> > > THEM.
> > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO

EXCEPTIONS........

> > > > bill
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a...,
> > > timg@k...
> > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this

to

> > be a
> > > sister site to the CCED group, as many of the same members are
> > there, for OT
> > > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY

POSTING

> > THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > > Yahoo! Groups Links
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,

wanliker@a...,

> > timg@k...
> > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to
> be a
> > sister site to the CCED group, as many of the same members are
> there, for OT
> > subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links