RE: [CAD_CAM_EDM_DRO] Help retrofitting
Posted by
Babar
on 2005-05-04 02:27:43 UTC
Dear Les,
Can you please guide me where in ini I can enter the
Offset value?
Since I don't have the data /manual of the drive there
fore I don't know about the mode of operation of these
drives i.e either Velocity or Torque Mode
Best Regards
Ubaidullah Babar
--- Leslie Watts <leswatts@...> wrote:
Do you Yahoo!?
Make Yahoo! your home page
http://www.yahoo.com/r/hs
Can you please guide me where in ini I can enter the
Offset value?
Since I don't have the data /manual of the drive there
fore I don't know about the mode of operation of these
drives i.e either Velocity or Torque Mode
Best Regards
Ubaidullah Babar
--- Leslie Watts <leswatts@...> wrote:
> Hi Babar__________________________________
>
> You can put in an offset in the .ini to counter this
> rotation,
> but you shouldn't have to. Are the amps running in
> velocity or torque mode?
>
> Les
>
> Leslie M.Watts
> L M Watts Furniture
> Tiger Georgia
> (706) 212-0242
>
> Main page:
> http://www.lmwatts.com
> Engineering:
> http://www.lmwatts.com/shop.html
> Cnc surplus for sale:
> http://www.lmwatts.com/forsale.html
> Carved signs:
> http://www.lmwatts.com/signwp.html
>
>
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com]On Behalf Of
> Babar
> Sent: Friday, April 29, 2005 2:47 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com;
> ubaid72@...
> Subject: [CAD_CAM_EDM_DRO] Help retrofitting
>
>
> Dear Friends,
>
> I am retrofitting a Bridgeport Milling with EMC and
> STG-II,
> The old controller is Heidenhain 151 and the DC
> servo
> Drives are Bosch Z15-1-240V.
>
> The problem I am facing is that when the drives are
> enable by STG II they start rotating due to some
> residual/offset voltage due to which EMC shows the
> following error and disables the drives.
>
> So I need to adjust the pots on Drive so that the
> motor does not rotate without any signal from STG
> II.
> But since I don't have the Manual of these drives I
> don't know how to adjust.
>
> Does anybody have some solution for this?
>
> regards
>
> Babar
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe:
> CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe:
> CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru
> Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I
> consider this to be a sister site to the CCED group,
> as many of the same members are there, for OT
> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC
> DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT
> ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
> CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>
>
>
>
>
>
Do you Yahoo!?
Make Yahoo! your home page
http://www.yahoo.com/r/hs
Discussion Thread
rdhorton4
2005-04-28 21:23:07 UTC
Little Machine Shop's DRO display - - voltage?
turbulatordude
2005-04-28 21:25:40 UTC
Re: Little Machine Shop's DRO display - - voltage?
Babar
2005-04-28 23:48:01 UTC
[CAD_CAM_EDM_DRO] Help retrofitting
Leslie Watts
2005-04-29 14:58:49 UTC
RE: [CAD_CAM_EDM_DRO] Help retrofitting
rdhorton4
2005-05-01 09:20:53 UTC
Re: Little Machine Shop's DRO display - - voltage?
Babar
2005-05-04 02:27:43 UTC
RE: [CAD_CAM_EDM_DRO] Help retrofitting
Leslie Watts
2005-05-04 05:03:51 UTC
RE: [CAD_CAM_EDM_DRO] Help retrofitting
Babar
2005-05-11 20:42:57 UTC
RE: [CAD_CAM_EDM_DRO] HeidenhainTNC 355 for Sale
Babar
2005-05-16 20:43:31 UTC
RE: [CAD_CAM_EDM_DRO] STG-II
Jon Elson
2005-05-16 21:24:52 UTC
Re: [CAD_CAM_EDM_DRO] STG-II